皮帶打滑檢測裝置DLK-III|打滑傳感器是麻城的皮帶輸送機上一種智能皮帶打滑檢測設備，它能夠及時檢測出皮帶輸送機的打滑故障，并發出報警信號，具有工作穩定性強，防護等級等特點，可廣泛用于各種帶式皮帶運輸系統。

皮帶打滑檢測裝置DLK-III|打滑傳感器防護等級，密封性好，可防水、放塵，防凝露，又名欠速開關、低速開關、打滑檢測器，是應用電感感應原理檢測設備的“正常旋轉”或“異常慢轉、停轉”。具有“自識別正常轉速”的智能功能，屬真正的欠速開關。當設備出現異常，轉速低于正常轉速的三分之二時，輸出“異常慢轉”信號。可為計算機及時反饋設備的運轉情況；也可直接用于設備保護。廣泛應用于提升機、皮帶機、等機械傳動設備因電器、機械故障引起的慢轉或停轉，以便及時處理，達到維護設備、保障的目的。

安裝使用： 
本機測速傳感器活動支架直接焊在輸送機橫梁處，使觸輪運行方向與膠帶平行，接觸良好。控制箱安裝帶式輸送機現場附近的墻壁上，并應防止振動。 
1）須定期清除積塵，檢驗開頭工作狀態； 
2）氣溫較低時，應在旋轉部位滴些潤滑油； 
3）出現故障應我公司或請人員維修。 
性能說明：        
本產品具有二種工作方式 
a． 檢測輸送帶的帶速  
b． 檢測輸送帶從動滾筒的轉速或旋轉設備的轉速  檢測儀內有四只繼電器,做為控制信號輸出。k1~k4繼電器的工作狀態受傳感頭實測數值同予置數值比較結果的控制,當實測數值大于或等于予置數值時, 繼電器為設定的狀態(“1”為吸合、 “0”為釋放),小于時開始延時（如果設定了轉換延時時間）時間到后轉換為設定的相反狀態。如果設置了起動延時時間,在起動時k2~k4將保持為設定狀態, 延時時間到已后進入檢測狀態。 通常情況下K1做為速度信號輸出（聯鎖起動時用） K2~K4做為打滑的報警輸出。
結構特性：
1.本機由控制箱與傳感器兩部份組成，控制箱采用密封措施，防法防水性能較好。傳感器為磁電式，安裝方便，可靠性。
2.由于控制部份采用CMOS電路，溫度適應性能較好。
帶速傳感器: 檢測帶速0.8～6.5m/s
           可檢測速度打滑率10％～50％
           防護等級：IP67
           供電電壓 220V,50Hz
           觸點容量 220V,5A
           一級打滑警告輸出   一組常開觸點，一組常閉觸點供程控使用。
           二級打滑報警輸出   一組常開觸點，一組常閉觸點供停機使用。

結構特點：

1、速度傳感器采用防水設計，鑄鐵式觸輪壽命更長； 

2、控制箱采用亮度LED數碼管顯示，*的速度狀態顯示功能； 
3、可設置5個速度狀態，獨立控制5組開關信號； 
4、5個速度狀態分別用不同的字符顯示方式，更直觀； 速度范圍可任意設置，速度范圍任意組合任意重疊； 
5、采用觸摸按鍵進行參數設置，靈活方便； 
6、采用寬電壓設計更適合復雜環境需求。

主要技術參數

用于帶式輸送機運行中膠帶與主動滾桶出現打滑（失速）故障。可防止由于打滑所造成的嚴重事故的發生。

Belt creep testing devi DLK - | slip sensor is macheng III on the research and development of belt conveyor belt creep testing equipment, a kind of inligen it can timely detect the slip fault belt conveyor, and send out alarm signals, with job stability is strong, high protection grade, etc, can be widely used in all kinds of belt conveyor belt transport system.
Belt creep testing devi DLK - III | skid sensor protection grade is high, good sealing, can waterproof, dust, prevent condensation, aka owe speed switch, low speed switch, skid detector, is the basis of the principle of inductan sensor detection equipment rotating the "normal" or "unusually slow turning, stalling. Inligent function with "self-recognition normal speed" is a real underspeed switch. When the devi is abnormal, the speed is less than two-thirds of the normal speed, and the output "abnormal slow turn" signal. Can provide the computer with timely feedback equipment operation; It can also be used directly for devi protection. It is widely used in lifting machine, belt machine, and other mechanical transmission equipment due to electrical and mechanical failure caused by slow turning or stopping, so as to timely handle, achieve the purpose of maintaining equipment and ensuring production.
Installation and use:
The machine special speed sensor movable bracket is directly welded to the beam of the conveyor, so that the running direction of the trolley is parallel to the belt and the contact is good. The control box shall be installed on the wall near the site of the belt conveyor and shall prevent vibration.
1) the dust should be cleared regularly to check the starting work status;
2) when the temperature is low, lubricate the rotating parts;
3) we should contact our company or ask for professional maintenan.
Performan description:
This product has two kinds of working methods.
A. Check the belt speed.
B. There are four relays in the speed detector of the conveyor belt driven drum rotating speed or rotating equipment, as the control signal output. K1 ~ k4 relay working condition by the sensing head with the measured values in the control of numerical comparn results, when the measured value is greater than or equal to the set value when the relay is set by the state (" 1 "and," 0 "for the release of the), is less than the start time delay (if set the delay time) time to convert after setting the opposite state. If the starting delay time is set, k2~k4 will remain in the set state when starting, and the delay time will enter the detection state after the delay. In general, K1 is used as the speed signal output (interlocking starting), K2~K4 as the alarm output for skidding.
Structural features:
1. The machine is composed of two parts: the control box and the sensor, the control box is sealed, and the waterproof property is better. The sensor is magnetic, easy to install and reliable.
2. Because the control part adopts CMOS circuit, the temperature ADAPTS well.
Speed sensor: the detection belt speed is 0.8 ~ 6.5m/s.
The speed of the detection rate is 10% ~ 50%.
Protection grade: IP67.
Power supply voltage 220V,50Hz.
Contact capacity 220V,5A.
Level 1 slide warning output a set of normally open contacts, a set of normally closed contacts for program-controlled use.
The secondary skid alarm output a set of normally open contacts, a set of normally closed contacts for the use of the stop.
Structural features:
1. The speed sensor adopts waterproof design, and the life of cast-iron contact wheel is longer;
2. The control box adopts high brightness LED digital tube to display the unique speed state display function;
3. Can set 5 speed states, independently control 5 sets of switch signals;
4. The five speed states are displayed in different characters and are more intuitive; Speed range can be arbitrarily set, the speed range arbitrary combination arbitrary overlap;
5. Use the touch button to set the parameters and be flexible and convenient;
6. Wide voltage design is more suitable for complex environmental needs.
Main technical parameters
Working voltage AC 220V 50HZ.
The machine power is 10W.
There are two Numbers behind the m/s decimal point.
Switch output light skid: 1 normally open, 1 normally closed; Heavy sliding: 1 normally open, 1 normally closed;
Relay contact capacity AC 380V 3A.
The analog output is 4 ~ 20mA, corresponding to 0 ~ Ve (rated speed). If you choose 0.75 ~ 1.0mm2 3-core shielding cable, connect the sensor and the host, the distan can be up to 1 km, so that the host and the upper computer can be close to each other, so that the analog quantity can be transferred easily.
Working temperature - 30 ~ + 40 ℃
Protection level sensor: IP65; Control box: IP54
When the relative humidity of 95% or less (25 ℃)
The distan of the sensor is no more than 7mm.
Belt skid detection devi DLK-III| skid sensor is used to slip (stall) failure of belt and active barrel during operation of belt conveyor. Can prevent the occurren of serious accidents caused by skidding.