Flo-Tech    43137-AE     流量傳感器顯示器    lower terminal location
C D
Terminal location
ADAMCZEWSKI
Elektronische Messtechnik GmbH
Felix-Wankel-Str. 13 74374 Zaberfeld
. +49 (0)7046-875 +49 (0)7046-7678
vertrieb@ad-messtechnik.de www.adamczewski。。ｃｏｍ
Analogue Memory AD-AS 320 GS
Description
Special characteristics
Optionally available functions
Application
)
The analogue memory AD-AS 320 GS serves the galvanic
separation, conversion and amplification of DC current signals
and voltage signals (0/4-20mA or 0/2-10V).
The device can save an analogue value over an unlimited
period.
With an active control signal (24V active or contact), the output
signal follows the input signal. If the control signal is
deactivated, the instantaneous output signal remains saved.
The saved value is also restored after a supply voltage failure.
Alternatively, the analogue value can also be taken over to the
output by pressing the memory key briefly.
An activation of zero trimmer and full trimmer is possible by
pressing the memory key for longer (only in signal sequence
mode). With this, the signal dimensions can be adjusted at the
front in the range of ±25%.
- the device has additionally a transmitter supply available.
- restoration of the last device condition (power cut)
- feedback contact with memory condition (closer)
- increased signal attenuation (max. 300s) possible at the works
- inverse function possible (i.e. 020mA in 200mA).
- optional linearization curve
Conversion, burden amplification and galvanic disconnection of
impressed transmitter signals, current signals and voltage signals
with additional memory function for maintenance work.
Specification
Type of construction: series housing 23x78x103mm (HxD)
Supply voltage wide range (20-253 VDC/50-253 VAC)
Power consumption max. 3,5VA or 2,2W
Input 0/4-20mA; 0/2-10V selectable via terminal
Transmitter supply 19V/max. 25mA (no-load run. approx. 26V)
Signal input resistance 50 Ohm at 20mA or 90kOhm at10V
Output 0/4-20mA; 0/2-10V (acc. to customer data)
Output burden < 500 Ohm/20mA or > 500 Ohm/10V
Damping (filter) as works parameter max. approx. 0.3 %/s
(linear, max. approx. 300s)
Remote control input 1030V (min. 200ms)
use transmitter supply for contact
Transient period/final oscillation time (10-90%) approx. 150 ms
Zero trimmer, full trimmer +/- 25 %
Linearizing curve 24 points (X/Y table in EEPROM)
LED (green) operation indicator, flashes with input
signal overflow
LED (rot) remains lit in memory mode, flashes every
5 seconds with activated trimmer
Linearity error: < 0.2 %
Temperature influence < 0.03% / K
Insulation test voltage input/output: 3.75 kV RMS
signal/supply:4 kV RMS
Protective systems input/output: against over voltage, crosspoling,
over current
power pack: against over current,
over voltage, over temperature
CE conformity: acc. to EN 50081-2, EN 50082-2
Ambient temperature: 0 to 50°C
weight max. 200 g
protection: IP 20
manner of fastening:
attachment rail: NS35/7,5
connection data:
fine-wire: 2,5 mm2
single-wire: 4 mm2
max. voltage: 250 V~
Connections and dimensions: AD-AS 320 GS
ADAMCZEWSKI
ZERO
SPAN
On Memory
Memoryr
update
AD-AS 320 GS
103
78
39
7 8
10 11
23
9
12
~~=
power-supply
0-10 V
0-20 mA
ground
+3
11 12
20-253 VDC
50-253 VAC (50-60Hz)
5 7 10
feeding +18V
0-20 mA
ground
+4
1
input U
input I
3,75 kV
4 kV
4 kV
+1
2
2
+6
remote
input
memory signallingcontact
+8
9
output 0/4-20 mA or
0/2-10 V
Transmitter
Further applications and
wiring examples
(see back page)
Printed 06/2010. We reserve the right for technical changes
ADAMCZEWSKI
Elektronische Messtechnik GmbH
Felix-Wankel-Str. 13 74374 Zaberfeld
. +49 (0)7046-875 +49 (0)7046-7678
vertrieb@ad-messtechnik.de www.adamczewski。。ｃｏｍ
Applications and wiring examples AD-AS 320 GS
Wiring examples with control contact (S)
input 10V
input
output
20mA / 10V
indicator contact
output
50-253VAC
20-253VDC
3
20mA
1
2
5
6
4
8
9
7
10
11
12
+
+ 18 V
+
control contact
(S)
Wiring examples with with activ control voltage (Us)
input 10V
input
output
20mA / 10V
indicator contact
output
50-253VAC
20-253VDC
3
20mA
1
2
5
6
4
8
9
7
10
11
12
+
+
control voltage
(Us)
1030 VDC
Printed 06/2010. We reserve the right for technical changes
ADAMCZEWSKI
Elektronische Messtechnik GmbH
Felix-Wankel-Str. 13 74374 Zaberfeld
. +49 (0)7046-875 +49 (0)7046-7678
vertrieb@ad-messtechnik.de www.adamczewski。。ｃｏｍ
Summation Amplifier AD-SMV 310 GS
AD-SMV 310 GB
AD-SMV 310 EV
Description
The summation amplifier adds or subtracts a maximum of 4-6
currents or voltages (terms of a sum), each signal can be
individually evaluated. The output signal (Current or voltage) is
proportional to the summation. signals, which have to be
subtracted, have to be connected interchanged. The output signal
(current or voltage) is stable up to the maximum load.
Important: Input and output must be galvanically separated.
Application
Analogue summation of single data. For example: flow-data,
levels, oxygen.
Ordering information
Following details are necessary for ordering:
1. arithmetical function
 for example: Output = Input 1 + Input 2 - Input 3
2. Input definition (order example):
 Input E1 = 0-20 mA = 0-500 cbm/h
Input E2 = 0-5 mA = 0-100 cbm/h
Input E3 = 0-20 mA = 0-150 cbm/h
Output A = 4-20 mA = 0-550 cbm/h
Power supply = 220 V AC
Specification
Power supply: GB : ALLPOWER 20-253V AC/DC
(*) EV : 230 V, 50-60 Hz or 20-30 VDC
Power consumption: approx. 2,5 VA or 2 W
Input: current or voltage
SMV 310 GB or GS: max 4 Inputs
SMV 310 EV: max 6 Inputs
Output: Current or voltage impressed
for example: 0-20mA, 4-20mA
or 0-10V
Max load: max. 800 Ohm at 20 mA
min. 500 Ohm at 10V
Linearity: < 0,5 %
Ambient temperature: 0 to + 50 °C
Printed 01/2008. We reserve the right for technical changes
1
8
7
6
5
4
3
2
9
160
100
80
4,2
21
Case Dimension
95x100x63mm
165
100
160
Stiftliste DIN 41612 Form F
on
128,4 (3HE)
30,48 (6TE)
ADAMCZEWSKI
span.
zero
3
2
9
8
12
11
4 1
5
6
+E1 7 10
-E1
+E2
-E2
-E3
+E3
+E4
-E4
+A
-A
-Uh
+Uh
E = Input, A= Output, Uh = power supply
1
2
3
4
5
6
7
8
9
+
~
~
+
+
Power-supply
20-253V AC/DC
Output
IN 4
IN 3
IN 1 .. IN 4
IN 2
IN 1
Output
+
~~
230 V, 50 Hz
20-30 VDC
b z
1
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
+
+
Input IN1
Input IN3
Input IN5
Input IN2
Input IN1IN6
Input IN4
Input IN6
Connections and dimensions:
AD-SMV 310 GB
weight max. 200 g
protection: IP 20
manner of fastening:
attachment rail: NS35/7,5
connection data:
fine-wire: 2,5 mm2
single-wire: 4 mm2
max. voltage: 250 V~
Connections and dimensions:
AD-SMV 310 GS
Connections and dimensions:
AD-SMV 310 EV
weight max. 300 g
protection: IP 30
weight max. 300 g
protection: IP 30
103
78
39
7 8
10 11
23
9
12
ADAMCZEWSKI
Front view
on
AD-SMV 310 GS
ADAMCZEWSKI
Elektronische Messtechnik GmbH
Felix-Wankel-Str. 13 74374 Zaberfeld
. +49 (0)7046-875 +49 (0)7046-7678
vertrieb@ad-messtechnik.de www.adamczewski。。ｃｏｍ
Burden Amplifier AD-BV 20 GVC
Description
Application
The burden amplifier AD-BV 20 GVC serves the power amplification
(burden increase) in application with high current loop resistance,
i.e. line resistance.
The burden amplifier is switched directly behind a present current
source (i.e. separation amplifier AD-TV 22 GL), whereby the energy
of the current source is also used.
The device output of the total device chain is optimally utilised. The
galvanic signal separation of the series separation amplifier
continues to be realised.
With applications, in which separation amplifiers with, for instance,
maximum 500 Ohm can no longer achieve the required burden voltage
for bridging high power resistance.
detachable terminal clamp
Specification
construction 1-channel switchboard housing
18x110x128mm (HxD) with
power-supply 20-253 VDC or 50-253 VAC
power-consumption max. 1 W / 1,5 VA
input 0/4–20 mA
input voltage consumption 6 V or 2 V with external wire link
(clamp 4 +5
output 0/4–20 mA (1:1 input/output
output load 1,3 kOhm or. 1 kOhm with external
wire link (clamp 4+5)
linearity error < 0,02 % of full scale
temperature influence < 10 ppm / K
insulation test voltage signal/power-supply 4 kV RMS (1 min)
protective systems input/output against over current
and over voltage
power-supply against over current,
over voltage and over temperature
(*) CE-conformity DIN EN 61326; DIN EN 55011(Kl. B)
ambient temperature 0 bis 50 °C
(*) During checking, slight signal deviations are possible
no galvanic separation to input!
Printed 09/2009. We reserve the right for technical changes
50-253 VAC / 20-253 VDC
2
1
11
10
7
8
20mA
20mA
5
4
RL
(high load)
input
optional external
wire link power-supply
amplifier
110
91
128 18
BV20
ADAMCZEWSKI
On
upper terminal
2 31 54 6
lower terminal
7 8 9 10 11 12
Terminal location
+
Connections and dimensions: AD-BV 20 GVC
weight: ca. 110 g
protection: IP 20
manner of fastening:
DIN rail 35mm (EN50022)
connection data:
fine-wire: 2,5 mm2
single-wire: 4,0 mm2
max. voltage: 250 V~
A B C D
A
C
B
 
AD-TV 2 GX
AD-TV 3 GX
AD-TV 10 GVB
AD-TV 24 GL
AD-TV 24 GVB
AD-TV 22 GVB 
AD-TV 22 GL 
AD-TV 40 GVC
AD-TV 30 GL
AD-TV 33 GL
AD-TV 32 GL
AD-TV 300 GS
AD-TV 310
AD-TV 320 GS
AD-TV 412 GS (2-channel)
AD-TV 200
AD-TV 201-204 (1-4 channel)
AD-TV 452 GVC
AD-TV 454 GVF
AD-TV 452 GS
AD-TV 350
AD-TV 380
AD-TV 810
AD-STV 2 GX 
AD-STV 24 GVB
AD-STV 24 GL
AD-STV 22 GVB
AD-STV 22 GL 
AD-STV 40 GVC
AD-STH 22 GL 
AD-STV 300 GS
AD-TV 320 GS
AD-STV 810 GS
AD-STVEX 710 GVD 
AD-TV 581 GS
AD-TV 591 GS
AD-TW 41 GM (1-channel)
AD-TW 41 ST (1-channel)
AD-TW 42 GS (2-channel)
AD-TW 41-48 EV
AD-TW 201 ST/GS (1-channel)
AD-TW 202 GS (2-channel)
AD-TW 401 (1-channel)
AD-TW 402-403 GS
AD-TW 401-408
AD-TWH 41 (1-channel)
AD-TW 501-502 
AD-TW 501-508 EV
AD-TW 601-602
AD-TW 601-608 EV
AD-TW 21
AD-TW 21/2 (2-channel)
AD-TW 21/3 (3-channel)
AD-TW 25
AD-TW 25/2 (2-channel)
AD-TW 25/3 (3-channel)
AD-MWT 21
AD-MWT 22
AD-MWT 24
AD-MWT 50
AD-TWT 24 GM
AD-TWT 21
AD-TWT 21/2 (2-channel)
AD-TWT 25
AD-TWT 25/2 (2-channel)
AD-VC3GVF-R0
AD-VC3GVF-R2
AD-VC3GVF-R4
AD-VC3B GVC-R0
AD-VC3B GVF-R2
AD-VC3B GVF-R4
AD-VC5GVF-R0
AD-VC5GVF-R2
AD-VC5GVF-R4
AD-VC5B GVC-R0
AD-VC5B GVF-R2
AD-VC5B GVF-R4
VarioCheck VC4S-R0
AD-VC4S-R2 (with 2 relays) 
AD-VC4S-R4 (with 4 relays)
AD-MV 110
AD-MV 50 GX
AD-MV 54 GX
AD-MV 50 GL 
AD-MV 54 GL
AD-MV 500 GS 
AD-MV 504 GS
AD-MV 544 GA (4-ch.)
AD-MW 200 ST
AD-MK 330
AD-MK 340 GVD
AD-SMK 330
AD-MK 530
AD-SAM 101
AD-SAM 201
VarioShow AD-VS8
VarioShow AD-VS8A4-G
VarioShow AD-VS8A4-S
VarioLog AD-VL8
VarioLog AD-VL8A4-G
VarioLog AD-VL8A4-S
AD-LM 6
AD-LM 12
AD-LM 16 
AD-LU 310 GVC
AD-LU 610 GVF
AD-LU 610 GA
AD-LU 110 GA
AD-LU 410 GA
AD-LU 120 GA
AD-LU 420 GA
AD-AI 200 GVC
AD-AF 100
AD-FM 250 GVC
AD-FM 210 GS
AD-FM 300 (1-channel)
AD-FM 600 (2-channel)
AD-IS 102 GVC (2 inputs)
AD-IS 106 GVF (6 inputs)
AD-IU 214 GVC
AD-AI 200 GVC
AD-KI 10 GX
AD-KI 100
AD-KV 100
AD-KR 11 GX
AD-KR 12 GX
AD-KR 22 GX
AD-BS 1
AD-BS 2
AD-BS 3
AD-NS 230
AD-üSE 2/2-xx
AD-üSE 2/3-xx
AD-üSE 2/4-xx
AD-üSE 3/2-xx
AD-üSE 3/3-xx
AD-üSE 3/4-xx
AD-üSK 3/2-xx
AD-üSK 3/3-xx
AD-üSK 3/4-xx
AD-RK 403
AD-RK 8/2
AD-RK 6/2U
AD-RK 403
AD-RK 8/2
AD-RK 6/2U
AD-SWG 211
AD-SWG 212 (2-channel)
AD-SWG 311
AD-SWG 312 (2-channel)
AD-TV 320
AD-SMV 400 GVC
AD-SMV 310
AD-MU 400 GVC
AD-AS 320
AD-NR 100
AD-ER 01
AD-ISW 100
AD-MMA 400 GVC
AD-BV 20 GVC
AD-SV 20
AD-SV 100
AD-EN-FM400GA_APPL
AD-EN-DA3
AD-EN-FM200GS
AD-EN-FM350GC
AD-EN-IS108EV
AD-EN-IS108GA
AD-EN-IU114
AD-EN-IU114GA
AD-EN-KR100
AD-EN-LW100
AD-EN-MA310
AD-EN-MI310
AD-EN-MK101
AD-EN-MK201
AD-EN-MK401
AD-EN-MU200GA
AD-EN-MV504
AD-EN-MV544GA
AD-EN-PW100GC
AD-EN-STV211
AD-EN-STV400GS
AD-EN-TV410
AD-EN-TV513GA
AD-EN-TV525
AD-EN-TV561GC
AD-EN-TV563GA
AD-EN-VC2AHeadquartes
CASAPPA S.p.A.
Via Balestrieri, 1
43044 Lemignano di Collecchio
Parma (Italy)
. (+39) 0521 30 41 11
(+39) 0521 80 46 00
IP Videoconferencing
: info@casappa.com
www.casappa。。ｃｏｍ
HYDRAULIC
PUMPS, MOTORS
& FILTERS
DOC 03 R A Edition: 03/04.2015 Replaces: DOC 02 R A
Constant evolution and a passion for hydraulics; this has been Casappa’s strategy, a privay owned company
that has been working for more than sixty years in the field of fluid power transmission.
We design and build the main components for the hydraulic system.
We listen to and work with our customers, from developing a new idea to after-sales service, anywhere around
the globe.
As a tight-knit group of highly motivated and professionally qualified people, we are always ready to meet new
challenges head on.
Thanks to the use of the most modern design engineering, simulation and lab testing technologies, we are
always flexible and ready to quickly modify our offer to meet market demands.
We are convinced that integrating electronics with hydraulics is instrumental to improve hydraulic control circuit
performance. For this reason we continuously invest in research & development, increasing the number of
electronic control and regulation parts in our system.
Quality is our total commitment: that’s why all of our products are thoroughly tested with constant monitoring
including data analysis and traceability. Further, specific tests are performed on machines in the field to verify
their effectiveness in their actual environment.
Casappa is worldwide recognized as a highly specialised manufacturer of hydraulic components.
We offer:
Fixed and variable displacement hydraulic pumps and motors
Hydraulic valves to control pressure and flow rate
Hydraulic filters
Our passion for high performance in hydraulic drives us.
Some of the major companies that rely on our specialised expertise and choose us as an important supplier of
hydraulic components for a wide range of applications include:
AGCO CATERPILLAR HUNAN SUNWARD JUNGHEINRICH SANDVIK VOLVO CE
ARGO TRACTORS CHENGGONG HUSQVARNA KOMATSU SANY XCMG
ASTRA Veicoli Industriali CNH HYUNDAI LINDE SCANIA YANMAR
ATLAS COPCO DAIMLER HYVA GROUP MANITOU GROUP STILL ZAPAGROMASCH
BAI-Brescia Antincendi Int. DOOSAN JCB MANITOWOC TEREX ZOOMLION
BOBCAT FARID JLG MAZ TEXTRON
BROKK GUIMA PALFINGER JOHN DEERE MERLO TORO
4 DOC 03 R A
DOC 03 R A 5
Product range
Aluminium body gear pumps and motors
Cast iron body gear pumps and motors
Aluminium body gear flow dividers
Cast iron body gear flow dividers
Fixed displacement axial piston pumps and motors
Variable displacement axial piston pumps
Hand pumps
6 DOC 03 R A
A complete range of high quality pumps
and motors, the end result of listening
carefully to what customers need and of
working closely with suppliers.
Headquarters:
CASAPPA S.p.A.
Via Balestrieri,1
43044 Lemignano Di Collecchio
Parma (Italy)
. (+39) 0521 30 41 11
(+39) 0521 80 46 00
IP Videoconferencing
: info@casappa.com
www.casappa。。ｃｏｍ
DOC 03 R A 7
Casappa offers nothing but the best value to its
customers thanks to the skills and expertise of
its workforce, investments in research and new
technologies, cooperation with leading universities
and electronics-hydraulics integration. Casappa offers a wide choice of gear or piston
pumps and motors for open-circuit applications.
Many functions, such as valves and controls, are
built directly into the products to optimise system
space and costs.
8 DOC 03 R A
POLARIS series
Gear pumps and motors built in three pieces with an extruded body in high resistance aluminium alloy. The wide choice of
shafts, flanges and ports, in compliance with all international standards (SAE, DIN and EUROPEAN) allow for their use in
an infinite variety of applications.
Displacements from 1,07 cm3/rev G 0.07 in3/rev to 91,10 cm3/rev G 5.56 in3/rev available in groups 10, 20 and 30.
Max. peak pressure up to 300 bar G 4350 psi.
Max. speed up to 4000 min?1.
Features
High efficiencies
Integrated outboard bearings for heavy duty
applications
Multiple units available in standard version,
common inlet and separated stages
Electro?hydraulic fan drive system
Custom design
Optional built-in valves
Anticavitation valves
Maximum pressure relief valves
Priority valves
Load?Sensing priority valves
By?pass electric valves
Proportional relief valves
Reverse valves
Main characteristics
Displacement Max. continuous
pressure
Max. speed
POLARIS 10 cm3/rev G in3/rev bar G psi min?1
PL. 10?1 1,07 G 0.07 260 G 3750 4000
PL. 10?1,5 1,60 G 0.10 260 G 3750 4000
PL. 10?2 2,13 G 0.13 260 G 3750 4000
PL. 10?2,5 2,67 G 0.16 260 G 3750 4000
PL. 10?3,15 3,34 G 0.20 260 G 3750 4000
PL. 10?4 4,27 G 0.26 250 G 3600 4000
PL. 10?5 5,34 G 0.33 250 G 3600 4000
PL. 10?5,8 6,20 G 0.38 230 G 3350 3500
PL. 10?6,3 6,67 G 0.41 230 G 3350 3500
PL. 10?8 8,51 G 0.52 180 G 2600 3500
PL. 10?10 10,67 G 0.65 140 G 2050 3500
POLARIS 20 cm3/rev G in3/rev bar G psi min?1
PL. 20?4 4,95 G 0.30 250 G 3600 4000
PL. 20?6,3 6,61 G 0.40 250 G 3600 4000
PL. 20?7,2 7,29 G 0.44 250 G 3600 4000
PL. 20?8 8,26 G 0.50 250 G 3600 3500
PL. 20?9 9,17 G 0.56 250 G 3600 3500
PL. 20?10,5 10,90 G 0.66 250 G 3600 3500
PL. 20?11,2 11,23 G 0.69 250 G 3600 3500
PL. 20?14 14,53 G 0.89 250 G 3600 3500
PL. 20?16 16,85 G 1.03 250 G 3600 3000
PL. 20?19 19,09 G 1.16 200 G 2900 3000
PL. 20?20 21,14 G 1.29 200 G 2900 3000
PL. 20?24,5 24,84 G 1.52 170 G 2450 2500
PL. 20?25 26,42 G 1.61 170 G 2450 2500
PL. 20?27,8 28,21 G 1.72 130 G 1900 2000
PL. 20?31,5 33,03 G 2.01 130 G 1900 2000
POLARIS 30 cm3/rev G in3/rev bar G psi min?1
PL. 30?22 21,99 G 1.34 250 G 3600 3000
PL. 30?27 26,70 G 1.63 250 G 3600 3000
PL. 30?34 34,55 G 2.11 240 G 3500 3000
PL. 30?38 39,27 G 2.40 240 G 3500 3000
PL. 30?43 43,98 G 2.68 230 G 3350 3000
PL. 30?51 51,83 G 3.16 210 G 3050 2500
PL. 30?61 61,26 G 3.74 190 G 2750 2500
PL. 30?73 73,82 G 4.50 170 G 2450 2500
PL. 30?82 81,68 G 4.98 160 G 2300 2200
PL. 30?90 91,10 G 5.56 150 G 2200 2200
NOTES
PL. : PLP = pump / PLM = motor
Aluminium body gear pumps and motors
DOC 03 R A 9
Aluminium body gear pumps
WHISPER series: low noise emission ? reduced pulsations by 75%
Gear pumps built in three pieces with an extruded body in high resistance aluminium alloy. WHISPER is a new and
original technology protected by international patents and applied to a family of external gear pumps that feature low noise
emissions. The wide choice of shafts, flanges and ports, in compliance with all international standards (SAE, DIN and
EUROPEAN) allow for their use in an infinite variety of applications.
Displacements from 1,12 cm3/rev G 0.07 in3/rev to 96,85 cm3/rev G 5.91 in3/rev available in groups 10, 20 and 30.
Max. peak pressure up to 300 bar G 4350 psi.
Max. speed up to 4000 min?1.
Features
High efficiencies
Low noise emission
Integrated outboard bearings for heavy duty
applications
Multiple units
Custom design
Optional built-in valves
Anticavitation valves
Maximum pressure relief valves
Priority valves
Load?Sensing priority valves
By?pass electric valves
Main characteristics
Displacement Max. continuous
pressure
Max. speed
WHISPER 10 cm3/rev G in3/rev bar G psi min?1
WSP 10?1 1,12 G 0.07 260 G 3750 4000
WSP 10?1,5 1,68 G 0.10 260 G 3750 4000
WSP 10?2 2,24 G 0.14 260 G 3750 4000
WSP 10?2,5 2,80 G 0.17 260 G 3750 4000
WSP 10?3,15 3,48 G 0.21 260 G 3750 4000
WSP 10?4 4,45 G 0.27 250 G 3600 4000
WSP 10?5 5,60 G 0.34 250 G 3600 4000
WSP 10?5,8 6,51 G 0.40 230 G 3350 3500
WSP 10?6,3 7,00 G 0.43 230 G 3350 3500
WSP 10?8 8,92 G 0.54 180 G 2600 3500
WSP 10?10 11,20 G 0.68 140 G 2050 3500
WHISPER 20 cm3/rev G in3/rev bar G psi min?1
WSP 20?4 5,25 G 0.32 250 G 3600 4000
WSP 20?6,3 7,00 G 0.43 250 G 3600 4000
WSP 20?7,2 7,72 G 0.47 250 G 3600 4000
WSP 20?8 8,74 G 0.53 250 G 3600 3500
WSP 20?9 9,65 G 0.59 250 G 3600 3500
WSP 20?10,5 11,54 G 0.70 250 G 3600 3500
WSP 20?11,2 11,89 G 0.73 250 G 3600 3500
WSP 20?14 15,39 G 0.94 250 G 3600 3500
WSP 20?16 17,84 G 1.09 250 G 3600 3000
WSP 20?19 20,22 G 1.23 200 G 2900 3000
WSP 20?20 22,38 G 1.37 200 G 2900 3000
WSP 20?24,5 26,30 G 1.60 170 G 2450 2500
WSP 20?25 27,98 G 1.71 170 G 2450 2500
WSP 20?27,8 29,87 G 1.82 130 G 1900 2000
WSP 20?31,5 34,98 G 2.13 130 G 1900 2000
WHISPER 30 cm3/rev G in3/rev bar G psi min?1
WSP 30?22 23,38 G 1.43 250 G 3600 3000
WSP 30?27 28,39 G 1.73 250 G 3600 3000
WSP 30?34 36,74 G 2.24 240 G 3500 3000
WSP 30?38 41,75 G 2.55 240 G 3500 3000
WSP 30?43 46,76 G 2.85 230 G 3350 3000
WSP 30?51 55,10 G 3.36 210 G 3050 2500
WSP 30?61 65,12 G 3.97 190 G 2750 2500
WSP 30?73 78,48 G 4.79 170 G 2450 2500
WSP 30?82 86,83 G 5.30 160 G 2300 2200
WSP 30?90 96,85 G 5.91 150 G 2200 2200
10 DOC 03 R A
Cast iron body gear pumps and motors
POLARIS “PH” series
Gear pumps and motors built in three pieces with cast iron body. The new gear pumps and motors “PH” series is an evolu?
tion of the “POLARIS” series. “POLARIS PH” has a new body made of cast iron to have higher operating parameters and
keep the full POLARIS versatility regarding shafts, flanges, ports and built-in valves.
This project is targeted for forklifts, skid steer loaders and all those applications where traditional aluminum pumps are
being pushed close to their limits. The possibility to mate the body with the cast iron covers further reduces noise levels, in
addition to increasing strength.
Displacements from 19,09 cm3/rev G 1.16 in3/rev to 33,03 cm3/rev G 2.01 in3/rev.
Max. peak pressure up to 300 bar G 4350 psi.
Max. speed up to 3500 min?1.
Main characteristics
Displacement Max. continuous
pressure
Max. speed
POLARIS PH 20 cm3/rev G in3/rev bar G psi min?1
PH. 20?19 19,09 G 1.16 250 G 3600 3500
PH. 20?20 21,14 G 1.29 250 G 3600 3500
PH. 20?23 23,32 G 1.42 250 G 3600 3000
PH. 20?24,5 24,84 G 1.52 230 G 3350 3000
PH. 20?25 26,42 G 1.61 230 G 3350 3000
PH. 20?27,8 28,21 G 1.72 200 G 2900 2500
PH. 20?31,5 33,03 G 2.01 200 G 2900 2500
NOTES
PH. : PHP = pump / PHM = motor
Features
High working pressure also for high displacements
Long service life
Low noise level
High volumetric efficiency also at high temperature
Inlet & Outlet optimization – High speed
Combination in multiple pumps
Built-in Valves simplify circuit design
Optional built-in valves
Anticavitation valves
Maximum pressure relief valves
Priority valves
Load?Sensing priority valves
By?pass electric valves
Proportional relief valves
Reverse valves
DOC 03 R A 11
Cast iron body gear pumps and motors
KAPPA series
Gear pumps and motors made of cast iron in two pieces. KAPPA is available with mounting flanges and side or rear ports
according to SAE and European standard. The rigidity of assembly ensure reliability and high volumetric efficiency also at
high operating pressures.
Displacements from 4,95 cm3/rev G 0.30 in3/rev to 73,82 cm3/rev G 4.50 in3/rev available in groups 20 and 30.
Max. peak pressure up to 330 bar G 4800 psi.
Max. speed up to 4000 min?1.
Features
High operating pressures
High efficiency at high temperature
Low noise emission
Optional built-in valves
Priority valves
Load?Sensing priority valves
Main characteristics
Displacement Max. continuous
pressure
Max. speed
KAPPA 20 cm3/rev G in3/rev bar G psi min?1
K. 20?4 4,95 G 0.30 285 G 4150 4000
K. 20?6,3 6,61 G 0.40 285 G 4150 4000
K. 20?8 8,26 G 0.50 285 G 4150 3500
K. 20?11,2 11,23 G 0.69 275 G 4000 3500
K. 20?14 14,53 G 0.89 265 G 3850 3500
K. 20?16 16,85 G 1.03 260 G 3750 3000
K. 20?20 21,14 G 1.29 210 G 3050 3000
K. 20?25 26,42 G 1.61 180 G 2600 2500
K. 20?31,5 33,03 G 2.01 140 G 2050 2500
KAPPA 30 cm3/rev G in3/rev bar G psi min?1
K. 30?27 26,70 G 1.63 280 G 4050 3000
K. 30?34 34,56 G 2.11 260 G 3750 3000
K. 30?38 39,27 G 2.40 260 G 3750 3000
K. 30?43 43,98 G 2.68 250 G 3600 3000
K. 30?51 51,83 G 3.16 230 G 3350 2500
K. 30?56 56,54 G 3.45 215 G 3100 2500
K. 30?61 61,26 G 3.74 200 G 2900 2500
K. 30?73 73,82 G 4.50 180 G 2600 2500
NOTES
K. : KP = pump / KM = motor
12 DOC 03 R A
Cast iron body gear pumps and motors
KAPPA COMPACT series
Gear pumps and motors made of cast iron in two pieces. A rigid and compact structure that makes it possible to
incorporate a number of functions in a limited space. The reduced dimensions as well as a large variety of drive shafts,
mounting flanges and ports ensure great flexibility in the “Compact” line.
Wide range of displacements: from 19,00 cm3/rev G 1.16 in3/rev to 150,79 cm3/rev G 9.20 in3/rev available in groups 25, 30,
35 and 40.
Max. peak pressure up to 325 bar G 4700 psi.
Max. speed up to 3500 min?1. Main characteristics
Displacement Max. continuous
pressure
Max. speed
KAPPA compact 25 cm3/rev G in3/rev bar G psi min?1
K. 25?19 19,00 G 1.16 280 G 4050 3500
K. 25?21 21,07 G 1.29 280 G 4050 3500
K. 25?23 23,06 G 1.41 280 G 4050 3500
K. 25?25 25,04 G 1.53 280 G 4050 3500
K. 25?27 27,03 G 1.65 280 G 4050 3500
K. 25?31 31,09 G 1.90 275 G 4000 3000
K. 25?34 34,03 G 2.08 275 G 4000 3000
K. 25?38 38,00 G 2.32 230 G 3350 3000
K. 25?43 43,01 G 2.62 210 G 3050 3000
KAPPA compact 30 cm3/rev G in3/rev bar G psi min?1
K. 30?22 21,99 G 1.34 280 G 4050 3000
K. 30?27 26,70 G 1.63 280 G 4050 3000
K. 30?31 30,63 G 1.87 260 G 3750 3000
K. 30?34 34,56 G 2.11 260 G 3750 3000
K. 30?38 39,27 G 2.40 260 G 3750 3000
K. 30?41 41,62 G 2.54 250 G 3600 3000
K. 30?43 43,98 G 2.68 250 G 3600 3000
K. 30?46 46,34 G 2.83 250 G 3600 3000
K. 30?51 51,83 G 3.16 230 G 3350 2500
K. 30?56 56,54 G 3.45 215 G 3100 2500
K. 30?61 61,26 G 3.74 200 G 2900 2500
K. 30?73 73,82 G 4.50 180 G 2600 2500
KAPPA compact 35 cm3/rev G in3/rev bar G psi min?1
KP 35?63 63,88 G 3.90 260 G 3750 3000
KP 35?71 72,40 G 4.42 260 G 3750 3000
KP 35?80 80,91 G 4.94 260 G 3750 3000
KP 35?90 91,56 G 5.59 245 G 3550 2500
KP 35?100 100,08 G 6.10 230 G 3350 2500
KAPPA compact 40 cm3/rev G in3/rev bar G psi min?1
K. 40?63 61,43 G 3.75 300 G 4350 2800
K. 40?73 72,60 G 4.43 300 G 4350 2800
K. 40?87 86,56 G 5.28 280 G 4050 2800
K. 40?109 108,90 G 6.64 250 G 3600 2800
K. 40?121 121,80 G 7.43 230 G 3350 2500
K. 40?133 134,03 G 8.18 220 G 3200 2500
K. 40?151 150,79 G 9.20 200 G 2900 2500
NOTES
K. : KP = pump / KM = motor
Features
High operating pressures
Low noise emission
Exceptional working life expectancy
Solid and compact design
Custom design
Optional built-in valves
Antishock and anticavitation valves
Priority valves
Load?Sensing priority valves
By?pass electric valves
DOC 03 R A 13
Cast iron body gear pumps
FORMULA and FORMULA SFP series
Gear pumps made of cast iron in two pieces, ideal for truck application.
Displacements from 8,26 cm3/rev G 0.50 in3/rev to 150,79 cm3/rev G 9.20 in3/rev available in groups 20, 30, 35 and 40.
Max. peak pressure up to 325 bar G 4700 psi.
Max. speed up to 3000 min?1.
Features
High performance also at very low speed
Different ports position availability
Low noise emission
Shaft seal system no leakage guarantee
Modular design
Direct mounting on the PTOs
Main characteristics
Displacement Max. continuous
pressure
Max. speed
FORMULA 20 cm3/rev G in3/rev bar G psi min?1
FP 20?8 8,26 G 0.50 280 G 4050 2000
FP 20?11,2 11,23 G 0.69 280 G 4050 2000
FP 20?16 16,85 G 1.03 280 G 4050 2000
FP 20?20 21,14 G 1.29 260 G 3750 2000
FP 20?25 26,42 G 1.61 220 G 3200 2000
FP 20?31,5 33,03 G 2.01 190 G 2750 1800
FP 20?36 35,94 G 2.19 170 G 2450 1800
FP 20?40 39,64 G 2.42 160 G 2300 1800
FORMULA 30 cm3/rev G in3/rev bar G psi min?1
FP 30?17 17,28 G 1.05 290 G 4200 3000
FP 30?27 26,70 G 1.63 290 G 4200 3000
FP 30?34 34,56 G 2.11 280 G 4050 2800
FP 30?38 39,27 G 2.40 280 G 4050 2800
FP 30?43 43,98 G 2.68 270 G 3900 2500
FP 30?51 51,83 G 3.16 240 G 3500 2500
FP 30?61 61,26 G 3.74 220 G 3200 2000
FP 30?73 73,82 G 4.50 200 G 2900 1800
FP 30?82 81,68 G 4.98 190 G 2750 1800
FP 30?100 100,52 G 6.16 180 G 2600 1800
FP 30?125 125,66 G 7.67 160 G 2300 1800
FORMULA 40 cm3/rev G in3/rev bar G psi min?1
FP 40?63 61,43 G 3.75 290 G 4200 2700
FP 40?73 72,60 G 4.43 280 G 4050 2700
FP 40?87 86,56 G 5.28 260 G 3750 2700
FP 40?109 108,90 G 6.64 240 G 3500 2700
FP 40?133 134,03 G 8.18 220 G 3200 2500
FP 40?151 150,79 G 9.20 180 G 2600 2500
FORMULA SFP 30 cm3/rev G in3/rev bar G psi min?1
SFP 30?34 35,43 G 2.16 280 G 4050 2800
SFP 30?43 45,09 G 2.75 270 G 3900 2500
SFP 30?51 53,14 G 3.24 250 G 3600 2500
SFP 30?61 62,80 G 3.83 230 G 3350 2500
SFP 30?73 75,68 G 4.62 205 G 2950 2250
SFP 30?82 83,74 G 5.11 195 G 2800 2250
FORMULA SFP 35 cm3/rev G in3/rev bar G psi min?1
SFP 35?90 95,99 G 5.86 230 G 3350 2250
SFP 35?100 104,92 G 6.40 220 G 3200 2250
SFP 35?112 118,31 G 7.22 205 G 2950 2250
14 DOC 03 R A
Cast iron body gear pumps and motors
MAGNUM series
Gear pumps and motors made of cast iron in three pieces. An extremely versatile and reliable design, also in the most
extreme operating conditions.
Displacements from 17,28 cm3/rev G 1.05 in3/rev to 125,63 cm3/rev G 7.66 in3/rev available in groups 30 and 35.
Max. peak pressure up to 320 bar G 4650 psi.
Max. speed up to 3000 min?1.
Main characteristics
Displacement Max. continuous
pressure
Max. speed
MAGNUM 30 cm3/rev G in3/rev bar G psi min?1
HD. 30?17 17,28 G 1.05 280 G 4050 3000
HD. 30?22 21,99 G 1.34 280 G 4050 3000
HD. 30?24 24,03 G 1.47 280 G 4050 3000
HD. 30?27 26,70 G 1.63 280 G 4050 3000
HD. 30?34 34,56 G 2.11 270 G 3900 3000
HD. 30?38 39,27 G 2.40 270 G 3900 3000
HD. 30?43 43,98 G 2.68 260 G 3750 3000
HD. 30?51 51,83 G 3.16 230 G 3350 2500
HD. 30?56 56,55 G 3.45 215 G 3100 2500
HD. 30?61 61,26 G 3.74 200 G 2900 2000
HD. 30?73 73,82 G 4.50 190 G 2750 1700
HD. 30?82 81,68 G 4.98 170 G 2450 1500
MAGNUM 35 cm3/rev G in3/rev bar G psi min?1
HD. 35?40 40,46 G 2.47 270 G 3900 3000
HD. 35?50 51,10 G 3.12 270 G 3900 3000
HD. 35?63 63,88 G 3.90 270 G 3900 3000
HD. 35?71 72,40 G 4.42 250 G 3600 3000
HD. 35?80 80,91 G 4.94 250 G 3600 3000
HD. 35?90 91,56 G 5.59 230 G 3350 2700
HD. 35?100 100,08 G 6.10 210 G 3050 2700
HD. 35?112 112,85 G 6.88 190 G 2750 2700
HD. 35?125 125,63 G 7.66 170 G 2450 2500
NOTES
HD. : HDP = pump / HDM = motor
Features
Wide range of drive shafts and flanges in SAE
version
More choices of port locations
Integrated outboard bearings for heavy duty
applications
Multiple units available in standard version,
common inlet and separated stages
Exceptional working life expectancy
DOC 03 R A 15
Aluminium body gear flow dividers
POLARIS series
Gear flow dividers made of high resistance aluminium alloy. These components can be used as flow equalizers, flow
dividers and pressure intensifiers.
Displacements from 2,14 cm3/rev G 0.13 in3/rev to 33,03 cm3/rev G 2.01 in3/rev available in groups 10 and 20.
Max. peak pressure up to 280 bar G 4050 psi.
Main characteristics
Displacement Max. continuous
outlet pressure
Max. speed
POLARIS 10 cm3/rev G in3/rev bar G psi min?1
PLD 10?2 2,14 G 0.13 250 G 3600 4200
PLD 10?3,15 3,34 G 0.20 250 G 3600 3990
PLD 10?4 4,27 G 0.26 250 G 3600 3940
PLD 10?5 5,34 G 0.33 250 G 3600 3680
PLD 10?6,3 6,67 G 0.41 250 G 3600 3500
POLARIS 20 cm3/rev G in3/rev bar G psi min?1
PLD 20?4 4,95 G 0.30 250 G 3600 4100
PLD 20?6,3 6,61 G 0.40 250 G 3600 3970
PLD 20?8 8,26 G 0.50 250 G 3600 3850
PLD 20?11,2 11,23 G 0.69 250 G 3600 3660
PLD 20?14 14,53 G 0.89 250 G 3600 3460
PLD 20?16 16,85 G 1.03 200 G 2900 3335
PLD 20?20 21,14 G 1.29 200 G 2900 3125
PLD 20?25 26,42 G 1.61 200 G 2900 2900
PLD 20?31,5 33,03 G 2.01 200 G 2900 2660
Features
Modular design
Accurate division of flow
Built?in relief valves
Combinations between different groups
16 DOC 03 R A
Cast iron body gear flow dividers
MAGNUM series
Gear flow dividers made of cast iron. These components can be used as flow equalizers, flow dividers and pressure
intensifiers.
Displacements from 17,28 cm3/rev G 1.05 in3/rev to 125,63 cm3/rev G 7.66 in3/rev available in groups 30 and 35.
Max. peak pressure up to 320 bar G 4650 psi.
Main characteristics
Displacement Max. continuous
outlet pressure
Max. speed
MAGNUM 30 cm3/rev G in3/rev bar G psi min?1
HDD 30?17 17,28 G 1.05 280 G 4050 3000
HDD 30?22 21,99 G 1.34 280 G 4050 3000
HDD 30?27 26,70 G 1.63 280 G 4050 3000
HDD 30?34 34,56 G 2.11 270 G 3900 3000
HDD 30?43 43,98 G 2.68 260 G 3750 3000
HDD 30?51 51,83 G 3.16 230 G 3350 2500
HDD 30?61 61,26 G 3.74 200 G 2900 2000
HDD 30?73 73,82 G 4.50 190 G 2750 1700
HDD 30?82 81,68 G 4.98 170 G 2450 1500
MAGNUM 35 cm3/rev G in3/rev bar G psi min?1
HDD 35?50 51,10 G 3.12 270 G 3900 3000
HDD 35?63 63,88 G 3.90 270 G 3900 3000
HDD 35?71 72,40 G 4.42 250 G 3600 3000
HDD 35?80 80,91 G 4.94 250 G 3600 3000
HDD 35?90 91,56 G 5.59 230 G 3350 2700
HDD 35?100 100,08 G 6.10 210 G 3050 2700
HDD 35?112 112,85 G 6.88 190 G 2750 2700
HDD 35?125 125,63 G 7.66 170 G 2450 2500
Features
Modular design
Accurate division of flow
High flow
Combinations between different groups
DOC 03 R A 17
Fixed displacement axial piston pumps
STRADA series
Fixed displacement bent axis piston pumps. STRADA pumps are ideally suited for PTOs applications in vehicles.
Displacements from 40,9 cm3/rev G 2.49 in3/rev to 110 cm3/rev G 6.71 in3/rev available in groups 32 and 37.
Max. peak pressure up to 400 bar G 5800 psi.
Max. speed up to 2950 min?1.
Main characteristics
Displacement Max. continuous
 pressure
Max. speed
STRADA 32 cm3/rev G in3/rev bar G psi min?1
BAP 32?40 40,90 G 2.49 350 G 5100 2950
BAP 32?50 50,10 G 3.06 350 G 5100 2750
BAP 32?63 63,00 G 3.84 350 G 5100 2450
BAP 32?71 71,60 G 4.37 315 G 4600 2250
BAP 32?80 78,30 G 4.78 315 G 4600 2200
STRADA 37 cm3/rev G in3/rev bar G psi min?1
BAP 37?80 79,10 G 4.83 350 G 5100 2500
BAP 37?110 110,00 G 6.71 300 G 4350 2300
Features
Low noise level
Direct mounting on the PTOs
Compact design
High volumetric, mechanical and overall efficiency
Available in ISO and UNI standard
18 DOC 03 R A
Fixed displacement axial piston pumps and motors
PLATA series
Fixed displacement axial piston pumps and motors swash plate design for open circuit applications. The design itself is
extremely compact while integrating a number of functions, with an electrically controlled valve on the pump and antishock
valves on the motor.
Unidirectional pumps LFP48: displacements from 27 cm3/rev G 1.65 in3/rev to 48,2 cm3/rev G 2.94 in3/rev.
Reversible motors LFM30: displacements from 22 cm3/rev G 1.34 in3/rev to 30,2 cm3/rev G 1.84 in3/rev.
Max. peak pressure up to 350 bar G 5100 psi.
Main characteristics
Displacement Max. continuous
 pressure
Max. speed
PLATA pumps cm3/rev G in3/rev bar G psi min?1
LFP 48?27 27,00 G 1.65 280 G 4050 2600
LFP 48?34 34,00 G 2.07 280 G 4050 2600
LFP 48?36,7 36,70 G 2.24 280 G 4050 2600
LFP 48?45,5 45,50 G 2.78 280 G 4050 2600
LFP 48?48 48,20 G 2.94 280 G 4050 2600
PLATA motors cm3/rev G in3/rev bar G psi min?1
LFM 30?22 22,00 G 1.34 280 G 4050 4900
LFM 30?26,5 26,50 G 1.62 280 G 4050 4800
LFM 30?28,5 28,50 G 1.74 280 G 4050 4700
LFM 30?30,2 30,20 G 1.84 280 G 4050 4500
Pumps features
Three?position electrically controlled valve with relief
valve
Electronic control of the rotor start?up and stop ramps
Rotation reverse with controlled delay
Easy integration with the machine cabin controls
Auxiliary gear pump with common suction, available
with either cast?iron or aluminium body
Motors features
Reversible rotation with integral antishock valves
European and SAE standard mounting flanges
Side or rear inlet options
Compact size
DOC 03 R A 19
Variable displacement axial piston pumps
PLATA LVP series
Variable displacement axial piston pumps swash plate design. PLATA pumps are ideally suited for medium and high
pressure open circuit applications.
Displacements from 28,70 cm3/rev G 1.75 in3/rev to 87,90 cm3/rev G 5.36 in3/rev.
Max. peak pressure up to 350 bar G 5100 psi.
Max. speed up to 3000 min?1.
Main characteristics
Max
displacement
Max. continuous
 pressure
Max. speed
PLATA LVP cm3/rev G in3/rev bar G psi min?1
LVP 30 28,70 G 1.75 280 G 4050 3000
LVP 48 45,40 G 2.77 280 G 4050 2600
LVP 75 73,60 G 4.49 280 G 4050 2600
LVP 90 87,90 G 5.36 250 G 3600 2200
Features
Energy savings
Low noise emission
Short response time
Drive shaft bearing suitable for radial and axial loads
Multiple combinations
Controls
Pressure compensator
Flow and pressure compensator (Load?Sensing)
Torque limiter
Electrohydraulic servocontrols
20 DOC 03 R A
Variable displacement axial piston pumps
MVP and MVPD series
Variable displacement axial piston pumps swash plate design ideally suited for open circuit in hydraulic applications.
The compact design allows to be mounted directly on engine motors.
The new “MVPD” series allow higher flow rates than traditional pumps with same dimensions, higher machine speeds
without affecting the design of the hydraulic system and a high power-to-dimensions ratio.
Displacements from 14 cm3/rev G 0.85 in3/rev to 84,7 cm3/rev G 5.17 in3/rev.
Max. peak pressure up to 350 bar G 5100 psi.
Max. speed up to 3700 min?1.
Main characteristics
Max
displacement
Max. continuous
 pressure
Max. speed
MVP cm3/rev G in3/rev bar G psi min?1
MVP 30.28 28,00 G 1.74 280 G 4050 3500
MVP 30.34 34,80 G 2.12 250 G 3600 2900
MVP 48.45 45,00 G 2.75 280 G 4050 3000
MVP 48.53 53,70 G 3.28 250 G 3600 2500
MVP 60.60 60,00 G 3.66 280 G 4050 3000
MVP 60.72 72,00 G 4.39 280 G 4050 2700
MVP 60.84 84,70 G 5.17 250 G 3600 2300
MVPD cm3/rev G in3/rev bar G psi min?1
MVPD 30.34 34,00 G 2.07 230 G 3350 3700
MVPD 30.45 45,00 G 2.75 230 G 3350 3500
MVPD 48.60 60,00 G 3.66 230 G 3350 2600
Features MVPD 48.65 65,00 G 3.97 230 G 3350 2800
Exceptional working life expectancy
Low noise emission
Drive shaft bearing suitable for radial and axial loads
Multiple combinations
Short response time
MVPD additional features
Higher speed
Higher power-to-weight ratio
Cost-optimized design
Controls
Min. and max. displacement limiter
Pressure compensator
Flow and pressure compensator (Load?Sensing)
Torque limiter
Electronic controls
DOC 03 R A 21
Variable displacement axial piston pumps
TVP series
Variable displacement axial piston pumps swash plate design ideally suited for open circuit truck applications.
The compact design allows to be mounted directly on the PTOs.
Displacements from 60,0 cm3/rev G 3.66 in3/rev to 84,7 cm3/rev G 5.17 in3/rev.
Max. peak pressure up to 400 bar G 5800 psi.
Max. speed up to 3000 min?1.
Main characteristics
Max
displacement
Max. continuous
 pressure
Max. speed
TVP cm3/rev G in3/rev bar G psi min?1
TVP 60.60 60,00 G 3.66 350 G 5100 3000
TVP 60.72 72,00 G 4.39 350 G 5100 2700
TVP 60.84 84,70 G 5.17 350 G 5100 2500
Features
Pump internal drain line
Compensators external drain line
Direct mounting on the PTOs
Body width 124,2 mm (4.8898 in)
Compact design
Low noise emission
Controls
Min. and max. displacement limiter
Flow and pressure compensator (Load?Sensing)
Electro-proportional pressure compensator
22 DOC 03 R A
Variable displacement axial piston pumps
PLATA SVP ? DVP series
Variable displacement axial piston pumps swash plate design for open circuit applications. SVP single flow, DVP dual
flow on piston pump and an additional piggybacked gear pump. The automatic overall torque limiter allows to optimize the
performance of themachine. SVP and DVP pumps has been designed specifically for mini excavators where compactness
and ease of installation are critical.
Piston pump: displacements from 7,8 cm3/rev G 0.48 in3/rev to 30 cm3/rev G 1.83 in3/rev.
Gear pump: displacements from 4,95 cm3/rev G 0.30 in3/rev to 21,14 cm3/rev G 1.29 in3/rev.
Max. speed up to 2600 min?1.
Main characteristics
Max
displacement
Max. continuous
 pressure
Max. speed
PLATA SVP cm3/rev G in3/rev bar G psi min?1
SVP 15,6 15,60 G 0.95 210 G 3050 2600
SVP 16 16,00 G 0.98 210 G 3050 2600
SVP 17 17,00 G 1.04 210 G 3050 2600
SVP 18 18,00 G 1.10 210 G 3050 2600
SVP 20 20,00 G 1.22 210 G 3050 2600
SVP 22 22,00 G 1.34 210 G 3050 2600
SVP 25 25,00 G 1.53 210 G 3050 2600
SVP 28 28,00 G 1.71 210 G 3050 2600
SVP 30 30,00 G 1.83 210 G 3050 2600
PLATA DVP cm3/rev G in3/rev bar G psi min?1
DVP 7,8 7,80x2 G 0.48x2 210 G 3050 2600
DVP 8 8,00x2 G 0.49x2 210 G 3050 2600
DVP 8,5 8,50x2 G 0.52x2 210 G 3050 2600
DVP 9 9,00x2 G 0.55x2 210 G 3050 2600
DVP 10 10,00x2 G 0.61x2 210 G 3050 2600
DVP 11 11,00x2 G 0.67x2 210 G 3050 2600
DVP 12,5 12,50x2 G 0.76x2 210 G 3050 2600
DVP 14 14,00x2 G 0.85x2 210 G 3050 2600
DVP 15 15,00x2 G 0.91x2 210 G 3050 2600
Gear pump cm3/rev G in3/rev bar G psi min?1
KP 20?4 4,95 G 0.30 285 G 4150 2600
KP 20?6,3 6,61 G 0.40 285 G 4150 2600
KP 20?8 8,26 G 0.50 285 G 4150 2600
KP 20?11,2 11,23 G 0.69 275 G 4000 2600
KP 20?14 14,53 G 0.89 265 G 3850 2600
KP 20?16 16,85 G 1.03 260 G 3750 2600
KP 20?20 21,14 G 1.29 210 G 3050 2600
SVP and DVP features
Compact design
Torque limiter
Energy savings
Low noise emission
Long service life
DOC 03 R A 23
Hand pumps
Up Easy series
Double acting hand pumps providing flow in both directions of lever movement.
Displacement from 12 cm3/cycle G 0.73 in3/cycle to 45 cm3/cycle G 2.75 in3/cycle.
Max. pressure 315 bar G 4600 psi.
Main characteristics
Displacement Max. pressure
Up Easy cm3/cycle G in3/cycle bar G psi
EP 12 12 G 0.73 315 G 4600
EP 25 25 G 1.53 250 G 3600
EP 45 45 G 2.75 220 G 3200
Features
New interchange modular design for maximum
flexibility
Same pumping group with or without reservoir
Suitable for auxiliary or emergency applications
24 DOC 03 R A
DOC 03 R A 25
Product range
Suction filters
In line filters spin-on
Tank mounted return line filters
Tank mounted return and suction line filters
In line medium and high pressure filters
Accessories
26 DOC 03 R A
IKRON “Fluid Filtration”, real specialist in
designing and manufacturing of hydraulic
filters. More than fifty years of experience
taught Casappa just how important filtering is
to optimise hydraulic control system efficiency
and to extend component service life.
Since its foundation, IKRON has followed the
ISO 9001 procedures, guaranteeing
the care and professionalism for which its
production has always been distinguished,
from design to delivery. This is why our
customers rely on IKRON every day.
IKRON S.r.l.
Via Prampolini, 2
43044 Lemignano Di Collecchio
Parma (Italy)
. (+39) 0521 30 49 11
(+39) 0521 30 49 00
IP Videoconferencing
: info@ikron.it
www.ikron.it
DOC 03 R A 27
IKRON uses virtual simulation tools during
the design phase to analyse and predict how
its products will behave when installed in the
hydraulic circuit.
Ikron offers a wide range of filters and accessories.
Suction filters, return filters, in line spin-on filters,
medium and high pressure filters.
Clogging indicators, level and temperature gauges,
filler breathers.
28 DOC 03 R A
HF 410 series
Flow up to 300 lpm G 79.3 US gpm
By-pass valve
Oversized filtering surface
HF 431-434-437 series
External tank connection
Aluminium head
Special version on request
Washable filtering media
Main characteristics
Nominal flow up to Degree of filtration*
Type l/min G US gpm MS (μm) MI (μm)
HF 410 300 G 79.3 90 25-60-125?250
HF 431 220 G 58.1 60-125?250
HF 434 160 G 42.3 60-125?250
HF 437 160 G 42.3 60-125?250
NOTES
(*): MS = zinc plated steel wire mesh / MI = stainless steel wire mesh
Suction filters
The tank submerged suction filters are designed to be fitted directly on pump intake and provide versatility to safeguard
the hydraulic components from contaminating particles.
Filters and accessories
DOC 03 R A 29
Filters and accessories
HF 620?625 series
Easy filtering elements replacement
Differential visual indicator
Interchangeable with major manufacturers
HF 650 series
Easy filtering elements replacement
High filtration performances
Operating pressure 35 bar G 510 psi
Interchangeable with major manufacturers
In line filters spin?on
These filters are specifically designed to be connected on the suction or in the return line of the hydraulic circuit and
provide versatility to safeguard the circuit components from contaminating particles.
Main characteristics
Nominal flow up to Operating pressure Degree of filtration*
Type l/min G US gpm bar G psi FG (μm) MS (μm) SP (μm) RP (μm)
HF 620 350 G 92.5 12 G 174 10?25 60?90?125 10?25
HF 625 220 G 58.1 25 G 360 10?25 60?90?125 10?25
HF 650 180 G 48 35 G 510 3?6?10?16?25 10?25
NOTES
(*): FG = micro?fibre glass / MS = zinc plated steel wire mesh / SP = cellulose / RP = reinforced cellulose
30 DOC 03 R A
HF 502 series
Operating pressure 8 bar G 115 psi
Interchangeable with major manufacturers
Filler cap
HF 508 series
Flow up to 1000 lpm G 264 US gpm
Double inlet port
Extension on the oil way out of the pipe union
Fluid-decelerating diffuser
HF 547 series
Air breather (available also with pressurized version)
Antisplash system
Anodized housing
Flange with four holes (only HF 547-20)
HF 554 series
Air breather (available also with pressurized version)
Antisplash system
Anodized housing
HF 570-575-578 series
Inside?to?outside flow direction
Magnetic pre?filtration
Filler cap
Interchangeable with major manufacturers
Main characteristics
Nominal flow up to Operating pressure Degree of filtration*
Type l/min G US gpm bar G psi FG (μm) MS (μm) MI (μm) SP (μm) RP (μm)
HF 502 630 G 166.5 8 G 115 3?6?10?25 90 25?60?125 10?25 10?25
HF 508 1000 G 264 8 G 115 3?6?10?25 90 25?60?125 10?25 10?25
HF 547 200 G 53 8 G 115 3?6?10?25 90 25?60?125 10?25 10?25
HF 554 630 G 166.5 8 G 115 3?6?10?25 90 25?60?125 10?25 10?25
HF 570 600 G 158 8 G 115 10?25 10?25
HF 575 1200 G 317 8 G 115 10?25 10?25
HF 578 1200 G 317 8 G 115 10?25 60?125 10?25
NOTES
(*): FG = micro?fibre glass / MS = zinc plated steel wire mesh / MI = stainless steel wire mesh/ SP = cellulose / RP = reinforced cellulose
Tank mounted return line filters
These filters are specifically designed to be directly connected on the hydraulic circuits return line and provide versatility to
safeguard the circuit components from contaminating particles.
Filters and accessories
DOC 03 R A 31
HF 525 series
Maximum operating pressure 12 bar G 174 psi
Internal by-pass set at 2,5 bar G 36 psi
Anti-cavitation valve with filter element
Main characteristics
Return flow
up to
l/min G US gpm
Suction flow
up to
l/min G US gpm
Operating
pressure
bar G psi
Degree of filtration*
Type FG (μm)
HF 525 270 G 71 42 G 160 12 G 174 10-25
NOTES (*): FG = micro-fibre glass
Tank mounted return and suction line filters
These filters are normally installed onto the tank and are used as the only solution to filter the oil flow coming from the
open circuit return line and to supply with filtered oil, pressurized at 0,5 bar (7.25 psi), the closed circuit of the suction line.
In line medium and high pressure filters
The in?line medium and high pressure filters are specifically designed to be connected on the pressure line of
the hydraulic circuit and provide versatility to safeguard the circuit components from contaminating particles.
HF 705 series
Sintered bronze filter element
Bidirectional flow
Aluminium housing
HF 710 series
Aluminium housing
Operating pressure 250 bar G 3600 psi
Compact design and lightness
By-pass valve
Filtration ratio ?x ≥ 200
Main characteristics
Nominal flow up to
l/min G US gpm
Operating
pressure
bar G psi
Degree of filtration*
Type FG (μm) SB (μm)
HF 705 115 G 30.4 350 G 5100 10-25-40-60
HF 710 47 G 12.4 250 G 3600 3?6?10?25
NOTES (*): FG = micro-fibre glass / SB = sintered bronze
Filters and accessories
32 DOC 03 R A
HF 725 series
CETOP 3 connections with reference to ISO4401
Operating pressure 350 bar G 5100 psi
Modular assembly
Compact design
Filtration ratio ?x ≥ 200
HF 733 - HF 735 series
Multilayer system
Flanged directly on valve blocks and hydraulic Power?Pack
Filtration ratio ?x ≥ 200
HF 743 - HF 745 - HF 748 series
Interchangeable with major manufacturers
Multilayer system
Filtration ratio ?x ≥ 200
HF 760-761 series
 Multilayer system
Wide range 20 ? 30 ? 40
Interchangeable with major manufacturers
Filtration ratio ?x ≥ 200
Main characteristics
Nominal flow
up to
l/min G US gpm
Operating
pressure
bar G psi
Degree of filtration*
Type FG (μm) MI (μm)
HF 725 20 G 5.3 350 G 5100 3?6?10?25 10-25
HF 733 80 G 21.1 250 G 3600 3?6?10?25
HF 735 150 G 39.7 320 G 4650 3?6?10?25
HF 743 95 G 25.1 250 G 3600 3?6?10?25
HF 745 170 G 45 310 G 4495 3?6?10?25
HF 748 145 G 38 280 G 4050 3?6?10?25
HF 760 450 G 120 420 G 6100 3?6?10?25
HF 761 420 G 111 420 G 6100 3?6?10?25
NOTES (*): FG = micro-fibre glass / MI = stainless steel wire mesh
In line medium and high pressure filters
Filters and accessories
DOC 03 R A 33
Filters and accessories
Accessories
Filler breathers - Air filters - Level and temperature gauges - Pressure gauges - Pressure/Vacuum gauges - Clogging
indicators: visual, electrical, visual differential and electrical visual differential.
34 DOC 03 R A

Headquartes
CASAPPA S.p.A.
 
& FILTERS
DOC 03 R A Edition: 03/04.2015 Replaces: DOC 02 R A? high quality fans 
? robust metal case
? Shock-and shake test according to the norms EN60068-2-6 and EN60068-2-27
? vibration-secured 
? temperature limiter 
DESCRIPTION ORDER INDEX
Kind of protection IP 20 -
Protection class PC I -
Operation- / storage temperature -40 – +70 °C -
WIring cable 0,50m 3x0,75mm2 * desired length
Heating element ceramic heating elements -
Mounting snap-mounting for 35mm DIN-rail -
screw-mounting (horizontal or vertical) Sw or Ss
Connection wiring cable 3x0,75mm2  AL
Temperature limiter 71°C +/- 7,5 K differantial gap -
Fan fan durability: 50.000h -
air power: 45m3 / h (free-blowing) -
blowing-out temperature: 40°C (250W); 110°C (500W,  -
optional in selectable form with a separate wiring cable SL
Mounting position vertical -
Special voltages 24V DC, 115V AC concrete info
HEATING
FAN HEATER
Type: Ventstar I
ORDER-NO. VOLTAGE POWER OPERA.CURRENT INRUSH CURRENT WEIGHT DIMENSIONS CONNECTION MOUNTING
230250VSAL0 230V AC 50/60 Hz 250W 1,09A 1,09A 1250g 135x83,60x82mm cable 0,50m snap
230400VSAL0 230V AC 50/60 Hz 400W 1,73A 1,73A 2000g 205x83,60x82mm cable 0,50m snap
230500VSAL0 230V AC 50/60 Hz 500W 2,17A 2,17A 2000g 205x83,60x82mm cable 0,50m snap
230800VSAL0 230V AC 50/60 Hz 800W 3,48A 3,48A 2000g 205x83,60x82mm cable 0,50m snap
Standard versions**
* variable length is possible
Power range: 250W – 800W
Voltage range: 24V – 230V
HEATING
wiring cable and snap-mounting wiring cable and screw-mounting
Dimensions
wiring cable and screw-mounting vertical
** further versions on request
Technical data Wiring diagram
Standard Special version Special version
Lm-therm Elektrotechnik AG
Sulzbachstra?e 15 - 94501 Aldersbach
T +49 (0) 85 43 - 6 24 60 30
E info@lm-therm.de
The information described on this data sheet contains descriptions or characteristics, which could not apply in the
described way in the concrete case. The information of the products can also change in the course of development.
The desired characteristics are only binding in the case that they have been explicitly agreed with a contract
conclusion. Delivery possibilities and technical changes reserved.
The mentioned technical data have been determined under labor conditions by universal test instructions. Only
insofar characteristics are ensured. The test for the suitability for the intended use scheduled by the purchaser is
incumbent on the purchaser; we do not take warranty for that. Errors reserved. Stand: 02/2015
代理德國威瑯WIELAND總線系統 
RICOS BC-DP SP05041910
RICOS EC-DP
RICOS SOCKET KNOT-DP
RICOS SOCKET FINAL-DP
RICOS SOCKET SWITCH
RICOS DP 16 I
RICOS DP 8 I/0
RICOS DP 16 O
RICOS DP 8I 8I/0
RICOS BC-S SP05041910
RICOS EC-S
RICOS SOCKET FEMALE-S
RICOS SOCKET MALE-S
RICOS S 16 I
RICOS S 16 I
RICOS S 8 I/0
RICOS S 16 O
RICOS S 8I 8I/0
S BC-CAN-DN SP05041910
RICOS EC-CAN-DN
RICOS CAN-DN 16 I
RICOS CAN-DN 8 I/0
RICOS CAN-DN 16 O
RICOS CAN-DN 8I 8I/0
BC-CANOPEN SP05041910
RICOS EC-CANOPEN
RICOS CANOPEN 16 I
RICOS CANOPEN 8 I/0
RICOS CANOPEN 16 O
RICOS CANOPEN 8I 8I/0
RICOS BC-ETHERNET
RICOS BC-ETHERNET PLC
RICOS 16 I
RICOS 8 I/O
RICOS 16 O
RICOS 8O NEG
RICOS 8O 2A
RICOS 8I 8I/O
RICOS 4AI / +-10V
RICOS 4AI / 10V
RICOS 4AI / 20MA
RICOS 4AI / 4-20MA
RICOS 4AI / PT100
RICOS 4AI / TC
RICOS 4AI4AO / +-10V
RICOS 4AI4AO / 10V
RICOS 4AI4AO / 20MA
RICOS 4AI4AO / 4-20MA
RICOS 4I AC 115V
RICOS 4I AC 230V
RICOS 4O RELAY
RICOS COUNTER
RICOS POSITION
RICOS RS 232/485
RICOS PV-A
RICOS TP PS-24VDC
RICOS TP PS-110VDC
RICOS TP PC-ETHERNET
RICOS TP BC-CANOPEN
RICOS TP BC-DP
RICOS TP BC-MVB
RICOS TP 8I DC 24V
RICOS TP 8I DC 110V
RICOS TP 8O DC 24V/1A
RICOS TP 8O DC 110V/1A
RICOS TP 4O DC 24V/3A
RICOS TP 4AI/PT100
RICOS TP 2AO U/I
RICOS TP 4AI2AO U/I
RICOS TP SET
RICOS TP SCREW
RICOS TP SPRING
RICOS TP CD-ROM
PODIS CON AS-I S PG
PODIS CON AS-I S LTG

德國威瑯WIELAND電源
WIPOS 24VDC/1,25A 1PH V
WIPOS 24VDC/2,0A 1PH V
WIPOS 24VDC/5,0A 1PH V
WIPOS 24VDC/5,0A 1PH H
WIPOS 24VDC/10A 1PH V
WIPOS 24VDC/10A 1PH H
WIPOS 24VDC/10A 3PH V
WIPOS 24VDC/20A 1PH V
WIPOS 24VDC/20A 1PH H
WIPOS 24VDC/20A 115AC H
WIPOS 24VDC/20A 3PH H
WIPOS 24VDC/40A 3PH H
德國威瑯WIELAND防雷器
WIE TAP BLOCK/3
WIE TAP BLOCK/1
WIE TAP IND 63A
WIE TAP IND 35A
WIE TAP LA B/N
WIE TAP GP C/T
WIE TAP PL T/C
WIE TAP V TNC 255
WIE TAP V TNS 255
WIE TAP V TT 255
WIE TAP GT TNC
WIE TAP GT TT
WIE TAP GT TNS
WIE TAP KAMM 3PH 6P
WIE TAP G 275
WIE TAP KAMM 1PH 4P
WIE TAP KAMM 1PH 57P
WIE TAP KAMM 3PH 57P
WIE TAP KAMM 4PH 56P
WIE TAP KAMM 2PH 16P
WIE TAP KAMM 2PH 22P
WIE TAP G 275 FM
WIE TAP PLT 275 FM
WIE TAP GT 275 FM
WIE TAP TB
WIE TAP R 230 FM
WIE TAP V SIGNAL
WIE TAM BCT VT AD 24V
WIE TAM GASABLEITER
WIE TAM PRUEFSTECKER
WIE TAM ERD.KLEMMENSATZ
WIE TAM GASABLEITER
WIE TAM PRUEFSTECKER
WIE TAM ERD.KLEMMENSATZ
WIE TAM BCT BASIS
WIE TAM EMV FEDERKLEMME
WIE TAM B 110V AC
WIE TAM ME 12V DC
WIE TAM ME 24V DC
WIE TAM ME 110V AC
WIE TAM MD 12V DC
WIE TAM MD 24V DC
WIE TAM MD 110V
WIE TAM MD 250V
WIE TAM ME/C 12V

量度和監控繼電器/電壓測量繼電器
SIM1001 AC/DC 0,1-15A;AC230V50-60HZ（A
SIM1001 AC/DC 2-500mA;AC230V50-60HZ（A）
SUM1001 AC/DC0,5-500V;AC230V50-60HZ（A）
SIM1001 AC/DC 0,1-15A;AC 42V50-60HZ（A）
SIM1001 AC/DC 0,1-15A;AC115V50-60HZ（A）
SIM1001 AC/DC 0,1-15A;AC 24V50-60HZ（A）
SIM1001 AC/DC 2-500mA;AC115V50-60HZ（A）
SIM1001 AC/DC 2-500mA;AC 24V50-60HZ（A） 
SUM1001 AC/DC0,5-500V;AC115V50-60HZ（A） 
SBW1005 5A 30S 3AC 440-480V 50-60Hz（B）
SXT32 0,5A 50-60HZ 110-127V 50-60HZ （A）
NMI1001 AC 2-500mA;AC 24V 50-60Hz
NMI1001 AC/DC 2-500mA DC24V
NMI1001 AC/DC2-500mA;AC230-240V 50-60Hz
NMI1001 AC/DC2-500mA;AC115-120V 50-60Hz
NMI1001 AC/DC 0,1-15A;AC24V 50-60Hz
NMI1001 AC/DC 0,1-15A;DC 24V 
NMI1001 AC/DC 0,1-15A;AC230-240V 50-60Hz
NMI1001 AC/DC 0,1-15A;AC115-120V 50-60Hz
量度和監控繼電器/電壓繼量繼電器NUM 1001
NMU1001 AC/DC 0,5-500V;AC24V 50-60Hz
NMU1001 AC/DC 0,5-500V;DC24V 
NMU1001AC/DC 0,5-500V;AC230-240V 50-60Hz
NMU1001AC/DC0,5-500V;AC115-120V 50-60Hz
SMS1005 AC 220-240V 50-60HZ （C） 
SMS1002 AC 220-240V 50-60HZ （D）
SMS1006 AC 220-240V 50-60HZ （A）
SMS1002 AC 110-127V 50-60HZ （D）
SMS1002-101 DC 24V （D）
SMS1061 AC 220-240V 50-60HZ （A）
SMS1062 AC 220-240V 50-60HZ （A）
SMS1002 AC 24V 50-60HZ （D）
STW1001 AC 220-240V 50-60HZ （B）
STW1002 AC 220-240V 50-60HZ （A）
STW1101 AC 220-240V 50-60HZ （A）
STW1102 AC 220-240V 50-60HZ （A）
STW1001 DC 24V （B）
KST12 1S AC 220-240V 50-60HZ （A）
SST12 1S AC 24V 50-60HZ （D）
SST12 1S AC 220-240V 50-60HZ （D）
KST12 1S AC 110V 50-60HZ （A）
SST12 1S AC 110-127V 50-60HZ （D）
NLT1001 （A）
NLT1003 （A）
STM1001 AC 220-240V 50-60HZ （B）
STM1003 AC 220-240V 50-60HZ （B）
電子合繼電器
NGS12 AC/DC 110-127V 50-60HZ （A）
NGS12 AC/DC 220-240V 50-60HZ （A）
NGS12 AC/DC 24V 50-60HZ （A）
NGS12 AC/DC 28V 50-60HZ （A）
KSP12 AC/DC 24V 50-60HZ （C）
KSP12 AC/DC 42-48V 50-60HZ （C）
KSP12 AC/DC 110-120V 50-60HZ （C）
KSP12 AC/DC 220-240V 50-60HZ （C）
SSF32 AC 24V 50-60HZ
SSF32 AC 230V 50-60HZ
SSF32 AC 110-120V 50-60HZ
SSF52 AC 110-120V 50-60HZ
SSF52 AC 24V 50-60HZ
SSF62 DC 24V
SSF52 AC 230V 50-60HZ
NGF31 AC/DC 24-240V 50-60HZ （A）
NGF32 AC/DC 24-240V 50-60HZ （A）
NGF52 AC/DC 24-240V 50-60HZ （A）
KID31K 99IMP AC/DC 24V 50-60HZ （A） 
SID32 99IMP AC 220-240V 50-60HZ （A）
SID32 99IMP AC 110-127V 50-60HZ （A）
KID31K 99IMP AC 230V 50-60HZ （A） 
SID32 999IMP AC 220-240V 50-60HZ （A）
UID51 AC/DC 24V
UID51 AC 110-240V

繼電器
WRS-SSAC1-250V6A
WRS-SSAC1-250V4A
RS-SSDC-60V3A
WRS-SSDC-60V5A
WRS-SSAC1-250V4A
WRS-SSAC1-250V6A
WRS-SSDC-60V3A
WRS-SSDC-60V5A
FLARE-24DC-1W-250V6A
FLARE-24V-1W-48V20M
FLARE-24DC-1W-250V6A-F
FLARE-24V-1S-250V6A-HA
FLARE-24DC-2W-250V6A-F
FLARE-24V-1W-48V20M-F
FLARE-12DC-1W-250V6A-F
FLARE-24V-1W-250V6A-CUT
FLARE-110V-1W-250V6A-F
FLARE-230V-1W-250V6A-F
FLARE MOVE 12VDC-1W-6A
FLARE MOVE 12VDC-1W-AU
FLARE MOVE 24VDC-1W-6A
FLARE MOVE 24VDC-1W-AU
FLARE MOVE 12V-1W-6A
FLARE MOVE 12V-1W-AU
FLARE MOVE 12VDC-1W-10A
FLARE MOVE 24VAC-1W-16A
FLARE MOVE 115AC-2W-8A
FLARE-24VDC/48VDC-0,5A
FLARE-24VDC/48VDC-2A
FLARE-115V/48VDC-0,5A
FLARE-230VAC/48VDC-0,5A
FLARE-24VDC/230VAC-0,5A
FLARE MOVE 48 24AC1W16AFlo-Tech    43137-AE     流量傳感器顯示器    
FLARE MOVE 48 12AC1W10A
FLARE MOVE 48 12DC1W10AFlo-Tech    43137-AE     流量傳感器顯示器    
FLARE MOVE 48 24DC2W8A
FLARE-TIMER-S-250V6A
FLARE-PID/0100-S-250V6A
WRS-REL-1S-250V5A