| General specifications |
|---|
| Slave type | Standard slave |
| AS-Interface specification | V3.0 |
| Required master specification | ≥ V2.0 |
| UL File Number | E223772 |
| Functional safety related parameters |
|---|
| MTTFd | 150 a |
| Mission Time (TM) | 20 a |
| Diagnostic Coverage (DC) | 0 % |
| Indicators/operating means |
|---|
| LED PWR/FAULT | dual LED green/red
green: AS-Interface voltage
red: communication error or address 0
green/red flashing: overload sensor supply or outputs |
| LED AUX | ext. auxiliary voltage UAUX ; LED green |
| LED IN | switching state (input); 4 LED yellow |
| LED OUT | Switching state (output); 4 LED yellow |
| Electrical specifications |
|---|
| Auxiliary voltage (output) | 24 V DC ± 15 % PELV |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface |
| Rated operating current | ≤ 30 mA (without sensors) / max. 230 mA |
| Protection class | III |
| Surge protection | UAUX, Uin: Over voltage category III, safe isolated power supplies (PELV) |
| Input |
|---|
| Number/Type | 4 inputs for 2- or 3-wire sensors (PNP), DC |
| Supply | from AS-Interface |
| Voltage | 21 ... 31 V |
| Current loading capacity | ≤ 200 mA (TB ≤ 40 °C),
≤ 160 mA (TB ≤ 60 °C), short-circuit protected |
| Input current | ≤ 9 mA (limited internally) |
| Switching point | according to DIN EN 61131-2 (Type 2) |
| | 0 (unattenuated) | ≤ 3 mA |
| | 1 (attenuated) | ≥ 5 mA |
| Output |
|---|
| Number/Type | 4 electronic outputs, PNP, overload and short-circuit proof |
| Supply | from external auxiliary voltage UAUX |
| Current | 1 A per output, 4 A total |
| Voltage | ≥ (UAUX - 0.5 V) |
| Compliance with standards and directives |
|---|
| Directive conformity | |
| | EMC Directive 2004/108/EC | EN 61000-6-2:2005, EN 61000-6-4:2007, EN 50295:1999 |
| Standard conformity | |
| | Noise immunity | EN 61000-6-2:2005, EN 50295:1999 |
| | Emitted interference | EN 61000-6-4:2007 |
| | Input | EN 61131-2:2007 |
| | Degree of protection | EN 60529:2000 |
| | Fieldbus standard | EN 50295:1999, IEC 62026-2:2006 |
| Programming instructions |
|---|
| Profile | S-7.0 |
| IO code | 7 |
| ID code | 0 |
| ID1 code | F |
| ID2 code | E |
| Data bits (function via AS-Interface) | input output |
| | D0 | IN1 OUT1 |
| | D1 | IN2 OUT2 |
| | D2 | IN3 OUT3 |
| | D3 | IN4 OUT4 |
| Parameter bits (programmable via AS-i) | function |
| | P0 | communication monitoring
P0 = 1 (default settings), monitoring = ON, i.e. if communication fails, the outputs are de-energised
P0 = 0, monitoring = OFF, if communication fails, the outputs maintain their condition |
| | P1 | not used |
| | P2 | not used |
| | P3 | not used |
| Ambient conditions |
|---|
| Ambient temperature | -25 ... 60 °C (-13 ... 140 °F) |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) |
| Relative humidity | 85 % , noncondensing |
| Climatic conditions | For indoor use only |
| Altitude | ≤ 2000 m above MSL |
| Pollution degree | 3 |
| Mechanical specifications |
|---|
| Degree of protection | IP65 |
| Connection | cable piercing method or terminal compartment
yellow flat cable/black flat cable or standard round cable
inputs/outputs:M12 x 1.5 cable glands and cage tension spring terminals |
| Material | |
| | Housing | PA 6 GF30 |
| Mass | 350 g |
| Tightening torque, housing screws | 0.8 Nm |
| Mounting | DIN rail or screw mounting |
