德國KAYSEN凱森泵業有限公司

Germany Kaysen Pump Co., Ltd.

凱森泵業總代理：營派閥門（上海）有限公司

詳細資料請登錄：營派閥門（上海）有限公司

進口不銹鋼潛水泵Germany Kaysen

德國KAYSEN凱森進口不銹鋼潛水泵概述
不銹鋼潛水泵是潛水泵的一種，因?yàn)橛泻芏酀撍玫牟馁|(zhì)是鑄鐵或者塑料的，如果僅僅用這些材質做出來的潛水泵，就很難滿足客戶的需求，如有很多有腐蝕性的介質就不能排放，如硫酸、鹽酸、硝酸等；這是它的其中一個特點。另外的特點就是除了不生銹外，還耐高溫。所以有很多廠家又生產了耐高溫不銹鋼潛水泵。雖然是不銹鋼，但是有很多輔助材料就耐不了多少高溫，一般在120°以內是沒有問題，如有些化工廠需要耐高溫200多度的還是得選用離心泵。

主要特點：

●不銹鋼潛水全部采用精密鑄造而成，除了能夠生產304的以外，還可以生產316、316L、等。

●采用不銹鋼設計的排水結構，因?yàn)橐话阄鬯枚加幸欢ǖ母g性和磨損，在設計上采用了耐磨，耐腐蝕的不銹鋼作為主要材料，它具有普通潛水排污泵的全部優點，同時增加了耐磨耐腐蝕的特點，擴大了適用范圍。

●不銹鋼自身有耐高溫性能，正常情況下可耐介質溫度50度左右，在德國巴赫公司的技術改進上可在100度以下的介質溫度定做。

●304的使用范圍在PH值4-10之間好用，如果超過該介質，建議使用316或者316L。

●電壓除了可以做220V和380V以外，還可以定做440V和660V電壓。

KAYSEN不銹鋼潛水泵圖片展示：

潛水泵日常維護

日常維護潛水泵每天檢查電源線。禁止漏水潛水泵運行。每天檢查泵體是否損壞，確保電機在工作時不漏氣。手術后，應及時清理附在泵上的碎屑，泵清洗。為確保潛水泵正常運行，您必須遵守這些要求。潛水泵使用前，應用兆歐表檢查電機的絕緣電阻，zui小值不得低于50M。灌水馬達應打開塞子，注滿清水，然后擰緊塞子，不要把灌溉塞子直接擰進井里。使用前檢查電纜是否有裂紋，以防破裂。如果損壞應該交換，以防止泄漏。潛水泵在進入水中之前應先怠速1-2分鐘，啟動兩次，檢查是否正常起動和怠速，轉向滿足要求。如果轉向，而不是交換任何兩相接線。檢查楊管是否有裂紋，聯軸器是否安全。潛水井下井和提升，絕不允許電纜本身，以避免損壞電纜或斷開接頭，造成不應有的事件。應該用電線或卡板和提升。電源電壓應控制在額定電壓的±5％范圍內，這樣電機才能正常工作。如果電壓過低或過高，電動機不能繼續使用，以免在工作過程中*損壞電機的過電壓或欠壓。立式潛水泵應浸入水中，不能傾斜。移到水下5米的水深是適當?shù)摹８吆沉康臐撍貌坏幂斔退蚰酀{。實際水頭潛水電泵應在額定電梯的0.8-1.1倍范圍內使用，以提高機組效率，節約能源，同時避免電機過載。潛水電動機的接線必須接入現實，避免燃燒電動機運行電動機相。電纜必須經常檢查是否有裂紋，劃痕等，有及時的更換或修理。如發現機油漏油，應及時向生產廠家進行維修或保養，更換密封件。電動機應定期清洗浸水沉砂池，更換電機內腔水。潛水泵運行六個月后，應進行維護檢查，更換損壞的部件。使用潛水泵后，水馬達應在馬達內部放入凈水，將泵抽干凈，油銹，并保持直立在干燥的地方。

Submersible Pumps Routine Maintenance

Submersible Pumps Routine Maintenance Check the power cord every day. The absolute prohibition of leakage water submersible pump operation. Checked daily pump body for damage, ensure that the motor does not leak at work. After the operation, you should promptly clean up the debris attached to the pump, the pump rinse. To ensure the normal operation of submersible pump, you must follow these requirements. Submersible pump before use, shall be checked with a megger insulation resistance of the motor, the value of the minimum of not less than 50M. The flooding irrigation motor should open the plug, filled with clean water and then tighten the plug, do not wring out the irrigation plug directly into the well. Check the cable for cracks before use, to break. If damage should be swapped to prevent leakage. Submersible pump should be before launching into the water, then idle for 1-2 minutes and start twice to check whether the normal starting and idling, turn to meet the requirements. If the steering Instead, you can swap any two-phase wiring. Check whether there are cracks Yang pipes, couplings are secure. submersable well pump to go down and lifting, never allow the cable itself, to avoid damage to the cable or disconnect joints, causing undue incidents. Should go down with wire or card board and lifting. Supply voltage should be controlled at the rated voltage of ± 5% range, so the motor to work properly. If the voltage is too low or too high, the motor can not continue to use, in order to avoid long-term motor overvoltage or undervoltage at work when damaged. Vertical submersible pump should be dipping into the water, not diagonal. Moving into the water depth of 5 meters under the water level is appropriate. Submersible pump high sand content shall not transport water or mud. Actual head submersible pump should be used within 0.8- 1.1 times the rated lift in order to improve unit efficiency, energy conservation, while avoiding motor overload. submersible electric motor wiring must be connected to reality, to avoid burning motor running motor phase. The cable must always check whether the cracks, scratches, etc., there is the timely replacement or repair. If motor oil leakage, it is timely to the manufacturer for repair or maintenance, replacement sealing element. Electric motor should be cleaned regularly flooding grit chamber, replace the motor cavity water. Submersible pump running after six months, should maintenance checks, replace the damaged parts. After using submersible pumps, water motor should put a net water inside the motor will pump clean, oiled rust and keep it upright in a dry place. 

進口不銹鋼潛水泵Germany Kaysen

位于德國SchwäbischGmünd的凱森Kaysen泵業有限公司是亞歐的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“德國制造”的可靠性和質量達到了zui高標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持亞歐各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。
        德國凱森始終堅持“重質量，講信譽”為宗旨。產品現全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。

        The Kaysen Pumps GmbH in SchwäbischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
          Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.