鋼板止水帶360x10規格@齊齊哈爾
在箱型基礎或地下室，底板和外墻板的混凝土是分開澆搗的，下次再澆搗墻板混凝土時，就有一條施工縫，當這條縫的位置在地下水位線以下時，就容易產生滲水。這樣就需要對這條縫進行技術處理，處理的方法很多，其中比較通行的方法是設置止水鋼板如圖。
Or the basement, in the box foundation slab and the slab concrete is cast separay, cast again next time wallboard, there is a construction joint, when the seam position is below the underground water level, is prone to water penetration. So you need to the seam technology processing, processing a lot of methods, one of the very popular method is to set up water stop plate as shown in figure.
而就在箱型基礎或地下室，底板和外墻板的混凝土是分開澆搗的，下次再澆搗墻板混凝土時，就有一條施工縫，當這條縫的位置在地下水位線以下時，就容易產生滲水。這樣就需要對這條縫進行技術處理，處理的方法很多，其中比較通行的方法是設置止水鋼板。即在澆筑下層混凝土時，預埋300*3的鋼板，其中有10-15cm的上部露在外面，在下次再澆筑混凝土時把這部分的鋼板一起澆筑進去，起到阻止外面的壓力水滲入的作用。一般鋼板止水帶是采用冷軋板作為母材,因為冷板厚度能夠均勻，熱板一般厚度達不到均勻的程度，厚度一般為2毫米或者3毫米，長度一般加工成3米長或者6米長，一般為三米好運輸。止水鋼板對焊接節點要求較高，不能出現漏點，影響防水性能。
Or the basement, and on the box foundation slab and the slab concrete is cast separay, when concrete is poured again next time wallboard concrete, there is a construction joint, when the seam position is below the underground water level, is prone to water penetration. So you need to the seam technology processing, processing a lot of methods, one of the very popular method is to set up water stop plate. Namely when casting lower concrete, embedded 300 * 3 steel plate, there are 10 to 15 cm exposed, the upper part of the next time when the concrete casting in this part of the plate together, have the effect of prevent outside the pressure of water infiltration. Manufacture steel plate water stop is commonly used as the parent metal, because of the cold plate thickness is uniform and the degree of thickness of hot plate generally not uniform, the thickness of 2 mm or 3 mm, length is generally processed into 3 meters or 6 meters long, usually for three meters. Check the demand is higher, shuicheng steel slabs welding node cannot be funnelled, affect the waterproof properties.
1、應盡力保證止水鋼板在墻體中線上；
2、兩塊鋼板之間的焊接要飽滿且為雙面焊 ，鋼板搭接不小于20mm；
3、墻體轉角處的處理，一、整塊鋼板彎折；二、丁字型焊接；三、7字型焊接。
4、止水鋼板的支撐焊接，可以用小鋼筋電焊在主筋上；
5、止水鋼板穿過柱箍筋時，可以將所穿過的箍筋斷開，制作成開口箍，電焊在鋼板上。
6、止水鋼板的“開口”朝迎水面。
1, should try our best to assure the centerline of the steel plate water stop in the wall;
2, between two pieces of steel plate welded to the full and the double-sided welding, steel plate lap should not less than 20 mm;
3, the processing of wall corner, one, the whole steel plate bending; Second, the t type welding; Three, seven type welding.
4, support welding of the steel plate water stop, can use small steel welded on the main reinforcement;
5, water stop plate through the column stirrup, can be through the stirrup disconnect, made into open collar, electric welding on the steel plate.
6, water stop plate "open" toward the face of the water.
