通信電纜 網絡設備 無線通信 云計算|大數據 顯示設備 存儲設備 網絡輔助設備 信號傳輸處理 多媒體設備 廣播系統 智慧城市管理系統 其它智慧基建產品
深圳市源拓光電技術有限公司
會員1.png)
深圳市源拓光電技術有限公司
| 參 考 價 | 面議 |
產品型號WT-SFP-T
品 牌
廠商性質生產商
所 在 地深圳市
聯系方式：錢嘉查看聯系方式
更新時間：2024-04-22 14:56:09瀏覽次數：124次
聯系我時，請告知來自 智慧城市網1
1. Feature:
l Up to 1.25 Gb/s bi-directional data links
l Hot-pluggable SFP footprint
l Low power dissipation(1.05W typical)
l Compact RJ-45 connector assembly
l Fully metal enclosure, for lower EMI
l RoHS compliant and lead-free
l Single +3.3V power supply
l 10/100/1000 BASE-T operation in host systems with SGMII interface
l 1.25 Gigabit Ethernet over Cat 5 cable
l Case operating temperature：
Commercial:
Extended:
Industrial:
2.PRODUCT DESCRIPTION
10/100/1000 BASE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) . They are compatible with the Gigabit Ethernet standards as specified in IEEE Std 802.3 .The 10/100/1000 BASE-T physical layer IC (PHY) can be accessed via I
10/100/1000 BASE-T is compatible with 1000BASE-X auto-negotiation, but does not have a link indication feature (RX_LOS is internally grounded).
3. SFP to Host Connector Pin Out
Figure 1. Diagram of host board connector block pin numbers and names
| Pin | Symbol | Name/Description | Ref. |
| 1 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
| 2 | TFAULT | Transmitter Fault. Not supported. |
|
| 3 | TDIS | Transmitter Disable. Not supported. |
|
| 4 | MOD_DEF(2) | Module Definition 2. Data line for Serial ID. | 2 |
| 5 | MOD_DEF(1) | Module Definition 1. Clock line for Serial ID. | 2 |
| 6 | MOD_DEF(0) | Module Definition 0. Grounded within the module. | 2 |
| 7 | Rate Select | No connection required |
|
| 8 | LOS | Loss of Signal indication. Logic 0 indicates normal operation. | 3 |
| 9 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 10 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 11 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 12 | RD- | Receiver Inverted DATA out. AC Coupled |
|
| 13 | RD+ | Receiver Non-inverted DATA out. AC Coupled |
|
| 14 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 15 | VCCR | Receiver Power Supply |
|
| 16 | VCCT | Transmitter Power Supply |
|
| 17 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
| 18 | TD+ | Transmitter Non-Inverted DATA in. AC Coupled. |
|
| 19 | TD- | Transmitter Inverted DATA in. AC Coupled. |
|
| 20 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
Notes:
1. Circuit ground is connected to chassis ground
2. Should be pulled up with 4.7k - 10k Ohms on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF(0) pulls line low to indicate module is plugged in.
3. LVTTL compatible with a maximum voltage of 2.5V. Not supported on WT-SFP-T.
The 10/100/1000 BASE-T has an input voltage range of 3.3 V +/- 5%. The 4V maximum voltage is not allowed for continuous operation.
| +3.3 Volt Electrical Power Interface | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Supply Current | Is |
| 320 | 375 | mA | 1.2W max power over full range of voltage ａnd temperature. See caution note below |
| Input Voltage | Vcc | 3.13 | 3.3 | 3.47 | V | Referenced to GND |
| Maximum Voltage | Vmax |
|
| 4 | V |
|
| Surge Current | Isurge |
|
| 30 | mA | Hot plug above steady state current. See caution note below |
Caution: Power consumption and surge current are higher than the specified values in the SFP MSA
Low-Speed Signals
MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VII, "Serial Communication Protocol"). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc
| Low-Speed Signals, Electronic Characteristics | |||||
| Parameter | Symbol | Min | Max | unit | Notes/Conditions |
| SFP Output LOW | VOL | 0 | 0.5 | V | 4.7k to 10k pull-up to host_Vcc, measured at host side of connector |
| SFP Output HIGH | VOH | host_Vcc -0.5 | host_Vcc + 0.3 | V | 4.7k to 10k pull-up to host_Vcc, measured at host side of connector |
| SFP Input LOW | VIL | 0 | 0.8 | V | 4.7k to 10k pull-up to Vcc, measured at SFP side of connector |
| SFP Input HIGH | VIH | 2 | Vcc + 0.3 | V | 4.7k to 10k pull-up to Vcc, measured at SFP side of connector |
6. High-Speed Electrical Interface
All high-speed signals are AC-coupled internally.
| High-Speed Electrical Interface, Transmission Line-SFP | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Line Frequency | fL |
| 125 |
| MHz | 5-level encoding, per IEEE 802.3 |
| Tx Output Impedance | Zout,TX |
| 100 |
| Ohm | Differential, for all frequencies between 1MHz and 125MHz |
| Rx Input Impedance | Zin,RX |
| 100 |
| Ohm | Differential, for all frequencies between 1MHz and 125MHz |
| High-Speed Electrical Interface, Host-SFP | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Single ended data input swing | Vinsing | 250 |
| 1200 | mV | Single ended |
| Single ended data output swing | Voutsing | 350 |
| 800 | mV | Single ended |
| Rise/Fall Time | Tr,Tf |
| 175 |
| psec | 20%-80% |
| Tx Input Impedance | Zin |
| 50 |
| Ohm | Single ended |
| Rx Output Impedance | Zout |
| 50 |
| Ohm | Single ended |
7.General Specifications
| General | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Data Rate | BR | 10 |
| 1000 | Mb/sec | IEEE 802.3 compatible. See Notes 2 through 4 below |
| Cable Length | L |
|
| 100 | m | Category 5 UTP. BER |
Notes:
1. Clock tolerance is +/- 50 ppm
2. By default, 10/100/1000 BASE-T is a full duplex device in preferred master mode
3. Automatic crossover detection is enabled. External crossover cable is not required
4. 10/100/1000 BASE-T operation requires the host system to have an SGMII interface with no clocks.
8. Environmental Specifications
| Environmental Specifications | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Case Operating Temperature | Tcase | 0 |
| 70 | °C | XGSF-T |
| -10 |
| 80 | °C | XGSF-T | ||
| -40 |
| 85 | °C | XGSF-T | ||
| Storage Temperature | Tsto | -40 |
| 85 | °C | Ambient temperature |
9. Serial Communication Protocol
10/100/1000 BASE-T support the 2-wire serial communication protocol outlined in the SFP MSA. It uses an Atmel AT
| Serial Bus Timing Requirements | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| I |
| 0 |
| 100,000 | Hz |
|
10. Mechanical Specifications (Unit:mm)
11.Contact :
| Address | 6/f, Bldg. 1, Sec. 3,South area, Honghualing Industrial Zone Xili Town,Nanshan District ,Shenzhen China |
| Zip | 518054 |
| Tel | |
| Fax | 086- |
| Website | |
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
智慧城市網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
